CULLMANN CUlight FR 60C - M: Wireless Flash Shooting with Manual Flash; Multi: Wireless Flash Shooting with Manual Flash

77
Auto Flash Shooting with Three Slave Unit
Setting <RATIO A:B C>.
2
● Use the same method of
step 1 and step 3 (Page
68) to set the master unit
as <RATIO A:B C>.
Setting the slave group
1 <C>.
● Use the same method of
step 1 (Page 68) to set the
slave unit of flash
group<C>.
Setting flash exposure
3 compensation.
● Use the same method of
step 1 (Page 68) to set the
slave unit of flash
group<C>.
● Press Function Button 2
< >. Turn the Select
Dial to set the amount of
flash exposure
compensation and
press<SET> button to
confirm.
A
B
C
About Slave Group Control
If three slave units are all set to
<A> in terms of slave ID, these
slave units will be controlled as if
they were one camera flash in
slave group A.
● When setting < RATIO A:B C >, group A, B and C will fire a
flash synchronously; when setting< RATIO A:B >, group C
will not fire a flash.
● If shooting under the situation that group C is toward the
main shooting subject, over exposure might occurred.
● In some EOS film cameras that support E-TTL autoflash,
you cannot perform multiple flash wireless shooting with a
flash ratio setting.
● The flash ratio of 8:1 to 1:1 to 1:8 is equivalent to 3:1 to 1:1
to 1:3 (1/2 step increment).
● The details of the flash ratio settings are as follows.
8:1 4:1 2:1 1:1 1:2 1:4 1:8
5.6:1 2.8:1 1.4:1 1:1.4 1:2.8 1:5.6
ID=A ID=A ID=A
6. M: Wireless Flash Shooting with Manual Flash
This describes wireless (multiple shooting) using manual flash. You
can shoot with a different flash output setting for each slave unit
(firing group). Set all parameters on the master unit.
Setting the number of flash
2 groups.
● When < > is
displayed, press the
Function Button 2
< > to set the
groups to fire.
● The setting changes as
follows each time you
press the button:
ALL(RATIO OFF)→
A/B(RATIO A:B)→
A/B/C(RATIO A:B:C)
Setting the flash mode to
1 <M>.
RATIO
Setting flash output.
3
● Press Function Button 3
< >. Turn the Select
Dial to set the flash output
of the groups. Press
<SET> button to confirm.
Taking the picture.
4
● Each group fires at the set
flash ratio.
● When ALL < RATIO OFF > is set, set A, B or C as the firing
group for the slave units.
● To fire multiple slave units with the same flash output,
select ALL < RATIO OFF > in step 2.
Setting <M> Flash Mode
You can directly operate the slave unit to manually set the manual
flash or stroboscopic flash.
Setting the slave unit.
1
Setting flash mode to <M>.
2
● Press <MODE> button so
that <M> is displayed.
● Set the manual flash
output. (Page 51)
MENU1
Gr
Slave Group A
7. Multi: Wireless Flash Shooting with Manual Flash
Setting <MULTI> stroboscopic
flash.
● Press <MODE> button so that
<MULTI> is displayed.
● Setting the stroboscopic flash.
(Page 52)
- 69 - - 70 -
6. M: Wireless Flash Shooting with
Manual Flash
This describes wireless (multiple shooting) using manual ash.
You can shoot with a different ash output setting for each slave
unit (ring group). Set all parameters on the master unit.
1
Setting the ash mode
to <M>.
2
Setting the number of ash
groups.
• When <
MENU 1
> is dis-
played, press the Function
Button 2 <
R ATIO
> to set
the groups to re.
• The setting changes as
follows each time you press
the button:
ALL (RATIO OFF) 
A/B (RATIO A:B) 
A/B/C (RATIO A:B:C)
3
Setting ash output.
• Press Function Button 3
<
Gr
>. Turn the Select Dial
to set the ash output of
the groups. Press < SET >
button to conrm.
4
Taking the picture.
• Each group res at the set
ash ratio.
• When ALL < RATIO OFF > is set, set A, B or C as the
ring group for the slave units.
• To re multiple slave units with the same ash output,
select ALL < RATIO OFF > in step 2.
Setting <M> Flash Mode
You can directly operate the slave unit to manually set the manu-
al ash or stroboscopic ash.
1
Setting the slave unit.
2
Setting ash mode to <M>.
• Press < MODE > button so
that < M > is displayed.
• Set the manual ash out-
put. (Page 58)
7. Multi: Wireless Flash Shooting with
Manual Flash
Setting <MULTI> stroboscopic
ash.
• Press <MODE> button so that
<MULTI> is displayed.
• Setting the stroboscopic ash.
(Page 59)
Auto Flash Shooting with Three Slave Unit
Setting <RATIO A:B C>.
2
● Use the same method of
step 1 and step 3 (Page
68) to set the master unit
as <RATIO A:B C>.
Setting the slave group
1 <C>.
● Use the same method of
step 1 (Page 68) to set the
slave unit of flash
group<C>.
Setting flash exposure
3 compensation.
● Use the same method of
step 1 (Page 68) to set the
slave unit of flash
group<C>.
● Press Function Button 2
< >. Turn the Select
Dial to set the amount of
flash exposure
compensation and
press<SET> button to
confirm.
A
B
C
About Slave Group Control
If three slave units are all set to
<A> in terms of slave ID, these
slave units will be controlled as if
they were one camera flash in
slave group A.
● When setting < RATIO A:B C >, group A, B and C will fire a
flash synchronously; when setting< RATIO A:B >, group C
will not fire a flash.
● If shooting under the situation that group C is toward the
main shooting subject, over exposure might occurred.
● In some EOS film cameras that support E-TTL autoflash,
you cannot perform multiple flash wireless shooting with a
flash ratio setting.
● The flash ratio of 8:1 to 1:1 to 1:8 is equivalent to 3:1 to 1:1
to 1:3 (1/2 step increment).
● The details of the flash ratio settings are as follows.
8:1 4:1 2:1 1:1 1:2 1:4 1:8
5.6:1 2.8:1 1.4:1 1:1.4 1:2.8 1:5.6
ID=A ID=A ID=A
6. M: Wireless Flash Shooting with Manual Flash
This describes wireless (multiple shooting) using manual flash. You
can shoot with a different flash output setting for each slave unit
(firing group). Set all parameters on the master unit.
Setting the number of flash
2 groups.
● When < > is
displayed, press the
Function Button 2
< > to set the
groups to fire.
● The setting changes as
follows each time you
press the button:
ALL(RATIO OFF)→
A/B(RATIO A:B)→
A/B/C(RATIO A:B:C)
Setting the flash mode to
1 <M>.
RATIO
Setting flash output.
3
● Press Function Button 3
< >. Turn the Select
Dial to set the flash output
of the groups. Press
<SET> button to confirm.
Taking the picture.
4
● Each group fires at the set
flash ratio.
● When ALL < RATIO OFF > is set, set A, B or C as the firing
group for the slave units.
● To fire multiple slave units with the same flash output,
select ALL < RATIO OFF > in step 2.
Setting <M> Flash Mode
You can directly operate the slave unit to manually set the manual
flash or stroboscopic flash.
Setting the slave unit.
1
Setting flash mode to <M>.
2
● Press <MODE> button so
that <M> is displayed.
● Set the manual flash
output. (Page 51)
MENU1
Gr
Slave Group A
7. Multi: Wireless Flash Shooting with Manual Flash
Setting <MULTI> stroboscopic
flash.
● Press <MODE> button so that
<MULTI> is displayed.
● Setting the stroboscopic flash.
(Page 52)
- 69 - - 70 -
Auto Flash Shooting with Three Slave Unit
Setting <RATIO A:B C>.
2
● Use the same method of
step 1 and step 3 (Page
68) to set the master unit
as <RATIO A:B C>.
Setting the slave group
1 <C>.
● Use the same method of
step 1 (Page 68) to set the
slave unit of flash
group<C>.
Setting flash exposure
3 compensation.
● Use the same method of
step 1 (Page 68) to set the
slave unit of flash
group<C>.
● Press Function Button 2
< >. Turn the Select
Dial to set the amount of
flash exposure
compensation and
press<SET> button to
confirm.
A
B
C
About Slave Group Control
If three slave units are all set to
<A> in terms of slave ID, these
slave units will be controlled as if
they were one camera flash in
slave group A.
● When setting < RATIO A:B C >, group A, B and C will fire a
flash synchronously; when setting< RATIO A:B >, group C
will not fire a flash.
● If shooting under the situation that group C is toward the
main shooting subject, over exposure might occurred.
● In some EOS film cameras that support E-TTL autoflash,
you cannot perform multiple flash wireless shooting with a
flash ratio setting.
● The flash ratio of 8:1 to 1:1 to 1:8 is equivalent to 3:1 to 1:1
to 1:3 (1/2 step increment).
● The details of the flash ratio settings are as follows.
8:1 4:1 2:1 1:1 1:2 1:4 1:8
5.6:1 2.8:1 1.4:1 1:1.4 1:2.8 1:5.6
ID=A ID=A ID=A
6. M: Wireless Flash Shooting with Manual Flash
This describes wireless (multiple shooting) using manual flash. You
can shoot with a different flash output setting for each slave unit
(firing group). Set all parameters on the master unit.
Setting the number of flash
2 groups.
● When < > is
displayed, press the
Function Button 2
< > to set the
groups to fire.
● The setting changes as
follows each time you
press the button:
ALL(RATIO OFF)→
A/B(RATIO A:B)→
A/B/C(RATIO A:B:C)
Setting the flash mode to
1 <M>.
RATIO
Setting flash output.
3
● Press Function Button 3
< >. Turn the Select
Dial to set the flash output
of the groups. Press
<SET> button to confirm.
Taking the picture.
4
● Each group fires at the set
flash ratio.
● When ALL < RATIO OFF > is set, set A, B or C as the firing
group for the slave units.
● To fire multiple slave units with the same flash output,
select ALL < RATIO OFF > in step 2.
Setting <M> Flash Mode
You can directly operate the slave unit to manually set the manual
flash or stroboscopic flash.
Setting the slave unit.
1
Setting flash mode to <M>.
2
● Press <MODE> button so
that <M> is displayed.
● Set the manual flash
output. (Page 51)
MENU1
Gr
Slave Group A
7. Multi: Wireless Flash Shooting with Manual Flash
Setting <MULTI> stroboscopic
flash.
● Press <MODE> button so that
<MULTI> is displayed.
● Setting the stroboscopic flash.
(Page 52)
- 69 - - 70 -
Auto Flash Shooting with Three Slave Unit
Setting <RATIO A:B C>.
2
● Use the same method of
step 1 and step 3 (Page
68) to set the master unit
as <RATIO A:B C>.
Setting the slave group
1 <C>.
● Use the same method of
step 1 (Page 68) to set the
slave unit of flash
group<C>.
Setting flash exposure
3 compensation.
● Use the same method of
step 1 (Page 68) to set the
slave unit of flash
group<C>.
● Press Function Button 2
< >. Turn the Select
Dial to set the amount of
flash exposure
compensation and
press<SET> button to
confirm.
A
B
C
About Slave Group Control
If three slave units are all set to
<A> in terms of slave ID, these
slave units will be controlled as if
they were one camera flash in
slave group A.
● When setting < RATIO A:B C >, group A, B and C will fire a
flash synchronously; when setting< RATIO A:B >, group C
will not fire a flash.
● If shooting under the situation that group C is toward the
main shooting subject, over exposure might occurred.
● In some EOS film cameras that support E-TTL autoflash,
you cannot perform multiple flash wireless shooting with a
flash ratio setting.
● The flash ratio of 8:1 to 1:1 to 1:8 is equivalent to 3:1 to 1:1
to 1:3 (1/2 step increment).
● The details of the flash ratio settings are as follows.
8:1 4:1 2:1 1:1 1:2 1:4 1:8
5.6:1 2.8:1 1.4:1 1:1.4 1:2.8 1:5.6
ID=A ID=A ID=A
6. M: Wireless Flash Shooting with Manual Flash
This describes wireless (multiple shooting) using manual flash. You
can shoot with a different flash output setting for each slave unit
(firing group). Set all parameters on the master unit.
Setting the number of flash
2 groups.
● When < > is
displayed, press the
Function Button 2
< > to set the
groups to fire.
● The setting changes as
follows each time you
press the button:
ALL(RATIO OFF)→
A/B(RATIO A:B)→
A/B/C(RATIO A:B:C)
Setting the flash mode to
1 <M>.
RATIO
Setting flash output.
3
● Press Function Button 3
< >. Turn the Select
Dial to set the flash output
of the groups. Press
<SET> button to confirm.
Taking the picture.
4
● Each group fires at the set
flash ratio.
● When ALL < RATIO OFF > is set, set A, B or C as the firing
group for the slave units.
● To fire multiple slave units with the same flash output,
select ALL < RATIO OFF > in step 2.
Setting <M> Flash Mode
You can directly operate the slave unit to manually set the manual
flash or stroboscopic flash.
Setting the slave unit.
1
Setting flash mode to <M>.
2
● Press <MODE> button so
that <M> is displayed.
● Set the manual flash
output. (Page 51)
MENU1
Gr
Slave Group A
7. Multi: Wireless Flash Shooting with Manual Flash
Setting <MULTI> stroboscopic
flash.
● Press <MODE> button so that
<MULTI> is displayed.
● Setting the stroboscopic flash.
(Page 52)
- 69 - - 70 -
R
616x0_CUlight_FR60X_BDA_Canon englisch.indd 77 24.10.2016 13:56:32