CULLMANN CUlight FR 60C - Page 32

76
Auto Flash Shooting with Three Slave Units
1
Setting the slave group
<C>.
• Use the same method of
step 1 (Page 75) to set the
slave unit of ash
2
Einstellung <RATIO A:B C>.
• Use the same method of
step 1 and step 3 (Page 75)
to set the master unit as
< RATIO A:B C >.
3
Setting ash exposure
compensation.
• Use the same method of
step 1 (Page 75) to set the
slave unit of ash group
< C >.
• Press Function Button 2
< >. Turn the Select
Dial to set the amount of
ash exposure compen-
sation and press < SET >
button to conrm.
About Slave Group Control
If three slave units are all set to
< A > in terms of slave ID, these
slave units will be controlled as
if they were one camera ash in
slave group A.
• When setting < RATIO A:B C >, Group A, B und C will
re a ash synchronously; when setting< RATIO A:B >,
Group C will not re a ash.
• If shooting under the situation that group C is toward the
main shooting subject, over exposure might occurred.
• In some EOS lm cameras that support E-TTL autoash,
you cannot perform multiple ash wireless shooting with
a ash ratio setting.
• The ash ratio of 8:1 to 1:1 to 1:8 is equivalent to 3:1 to
1:1 to 1:3 (1/2 step increment).
• The details of the ash ratio settings are as follows.
1:88:1 4:1 2:1 1:1 1:2 1:4
5.6:1 2.8:1 1.4:1 1:1.4 1:2.8 1:5.6
Auto Flash Shooting with Three Slave Unit
Setting <RATIO A:B C>.
2
● Use the same method of
step 1 and step 3 (Page
68) to set the master unit
as <RATIO A:B C>.
Setting the slave group
1 <C>.
● Use the same method of
step 1 (Page 68) to set the
slave unit of flash
group<C>.
Setting flash exposure
3 compensation.
● Use the same method of
step 1 (Page 68) to set the
slave unit of flash
group<C>.
● Press Function Button 2
< >. Turn the Select
Dial to set the amount of
flash exposure
compensation and
press<SET> button to
confirm.
A
B
C
About Slave Group Control
If three slave units are all set to
<A> in terms of slave ID, these
slave units will be controlled as if
they were one camera flash in
slave group A.
● When setting < RATIO A:B C >, group A, B and C will fire a
flash synchronously; when setting< RATIO A:B >, group C
will not fire a flash.
● If shooting under the situation that group C is toward the
main shooting subject, over exposure might occurred.
● In some EOS film cameras that support E-TTL autoflash,
you cannot perform multiple flash wireless shooting with a
flash ratio setting.
● The flash ratio of 8:1 to 1:1 to 1:8 is equivalent to 3:1 to 1:1
to 1:3 (1/2 step increment).
● The details of the flash ratio settings are as follows.
8:1 4:1 2:1 1:1 1:2 1:4 1:8
5.6:1 2.8:1 1.4:1 1:1.4 1:2.8 1:5.6
ID=A ID=A ID=A
6. M: Wireless Flash Shooting with Manual Flash
This describes wireless (multiple shooting) using manual flash. You
can shoot with a different flash output setting for each slave unit
(firing group). Set all parameters on the master unit.
Setting the number of flash
2 groups.
● When < > is
displayed, press the
Function Button 2
< > to set the
groups to fire.
● The setting changes as
follows each time you
press the button:
ALL(RATIO OFF)→
A/B(RATIO A:B)→
A/B/C(RATIO A:B:C)
Setting the flash mode to
1 <M>.
RATIO
Setting flash output.
3
● Press Function Button 3
< >. Turn the Select
Dial to set the flash output
of the groups. Press
<SET> button to confirm.
Taking the picture.
4
● Each group fires at the set
flash ratio.
● When ALL < RATIO OFF > is set, set A, B or C as the firing
group for the slave units.
● To fire multiple slave units with the same flash output,
select ALL < RATIO OFF > in step 2.
Setting <M> Flash Mode
You can directly operate the slave unit to manually set the manual
flash or stroboscopic flash.
Setting the slave unit.
1
Setting flash mode to <M>.
2
● Press <MODE> button so
that <M> is displayed.
● Set the manual flash
output. (Page 51)
MENU1
Gr
Slave Group A
7. Multi: Wireless Flash Shooting with Manual Flash
Setting <MULTI> stroboscopic
flash.
● Press <MODE> button so that
<MULTI> is displayed.
● Setting the stroboscopic flash.
(Page 52)
- 69 - - 70 -
Auto Flash Shooting with Three Slave Unit
Setting <RATIO A:B C>.
2
● Use the same method of
step 1 and step 3 (Page
68) to set the master unit
as <RATIO A:B C>.
Setting the slave group
1 <C>.
● Use the same method of
step 1 (Page 68) to set the
slave unit of flash
group<C>.
Setting flash exposure
3 compensation.
● Use the same method of
step 1 (Page 68) to set the
slave unit of flash
group<C>.
● Press Function Button 2
< >. Turn the Select
Dial to set the amount of
flash exposure
compensation and
press<SET> button to
confirm.
A
B
C
About Slave Group Control
If three slave units are all set to
<A> in terms of slave ID, these
slave units will be controlled as if
they were one camera flash in
slave group A.
● When setting < RATIO A:B C >, group A, B and C will fire a
flash synchronously; when setting< RATIO A:B >, group C
will not fire a flash.
● If shooting under the situation that group C is toward the
main shooting subject, over exposure might occurred.
● In some EOS film cameras that support E-TTL autoflash,
you cannot perform multiple flash wireless shooting with a
flash ratio setting.
● The flash ratio of 8:1 to 1:1 to 1:8 is equivalent to 3:1 to 1:1
to 1:3 (1/2 step increment).
● The details of the flash ratio settings are as follows.
8:1 4:1 2:1 1:1 1:2 1:4 1:8
5.6:1 2.8:1 1.4:1 1:1.4 1:2.8 1:5.6
ID=A ID=A ID=A
6. M: Wireless Flash Shooting with Manual Flash
This describes wireless (multiple shooting) using manual flash. You
can shoot with a different flash output setting for each slave unit
(firing group). Set all parameters on the master unit.
Setting the number of flash
2 groups.
● When < > is
displayed, press the
Function Button 2
< > to set the
groups to fire.
● The setting changes as
follows each time you
press the button:
ALL(RATIO OFF)→
A/B(RATIO A:B)→
A/B/C(RATIO A:B:C)
Setting the flash mode to
1 <M>.
RATIO
Setting flash output.
3
● Press Function Button 3
< >. Turn the Select
Dial to set the flash output
of the groups. Press
<SET> button to confirm.
Taking the picture.
4
● Each group fires at the set
flash ratio.
● When ALL < RATIO OFF > is set, set A, B or C as the firing
group for the slave units.
● To fire multiple slave units with the same flash output,
select ALL < RATIO OFF > in step 2.
Setting <M> Flash Mode
You can directly operate the slave unit to manually set the manual
flash or stroboscopic flash.
Setting the slave unit.
1
Setting flash mode to <M>.
2
● Press <MODE> button so
that <M> is displayed.
● Set the manual flash
output. (Page 51)
MENU1
Gr
Slave Group A
7. Multi: Wireless Flash Shooting with Manual Flash
Setting <MULTI> stroboscopic
flash.
● Press <MODE> button so that
<MULTI> is displayed.
● Setting the stroboscopic flash.
(Page 52)
- 69 - - 70 -
616x0_CUlight_FR60X_BDA_Canon englisch.indd 76 24.10.2016 13:56:28