Curtis 1238SE - Page 32

4 — PROGRAMMABLE PARAMETERS
Curtis 1232E/34E/36E/38E & 1232SE/34SE/36SE/38SE Manual, os 31 – May 2017 Return to TOC
pg. 28
Table 3 Programmable Parameters Menus: 1313/1314 Programmer continued
DRIVERS MENU........................ p. 51
— MAIN CONTACTOR......... p. 51
— Main Enable
— Main Interlock Type
— Pull In Voltage
— Holding Voltage
— Battery Voltage Comp.
— Interlock Type
— Open Delay
— Weld Check Enable
— Main DNC Check Enable
— Main DNC Check Threshold
— Precharge Enable
— PROPORTIONAL DRIVER... p. 53
— PD Enable
— Hyd Lower Enable
— PD Max Current
— PD Min Current
— PD Dither %
— PD Dither Period
— PD Kp
— PD Ki
— DRIVER 3...................... p. 53
— Contactor Enable
— Pull In Voltage
— Holding Voltage
MOTOR MENU........................................ p. 54
— Typical Max Speed
— CONTROL ALGORITHMS................... p. 55
— Motor Technology
— 0-ACIM (INDUCTION MOTOR)........ p. 55
— CHARACTERIZATION TEST........ p. 55
— Test Enable
— Test Throttle
— Motor Poles
— Max Test Speed
— Max Text Current
— SlipGain
— Current Reg Tuning Test Enable
— FIELD WEAKENING CONTROL... p. 56
— FW Base Speed
— Field Weakening Drive
— Weakening Rate Drive
— Min Field Current
— Swap Two Phases................... p. 57
— MotorType............................... p. 57
— LOS (Limited Operating Strategy)... p. 58
— LOS Upon Encoder Fault
— LOS Max Speed
— LOS Max Current
— LOS Max Mod Depth
— LOS Accel Rate
— LOS Decel Rate
— 1-SPM (SURFACE PM MOTOR)...... p. 59
— CHARACTERIZATION TESTS...... p. 59
— Test Enable
— Test Throttle
— Max Test Speed
— Max Test Current
BATTERY MENU................................. p. 62
— Nominal Voltage
— Kp UV
— Ki UV
— User Overvoltage
— User Undervoltage
— Reset Volts Per Cell
— Full Volts Per Cell
— Empty Volts Per Cell
— Discharge Time
— BDI Reset Percent
— MOTOR FEEDBACK OPTIONS.............. p. 59
— Feedback Type
— Swap Feedback Direction
— 1-ENCODER................................. p 59
— Encoder Steps
— ENCODER FAULT SETUP.......... p. 60
— Fault Detection Enable
— Encoder Pulse Fault Detect Time
— Fault Stall Time
— 2-SIN/COS................................... p. 60
— Sin Cos Fault Threshold
— Sin Cos Fault Threshold High
— Sin Cos Fault Time
— Sin Min
— Sin Max
— Cos Min
— Cos Max
— TEMPERATURE CONTROL............. p. 61
— Sensor Enable
— Sensor Type
— Sensor Offset
— Braking Thermal Cutback Enable
— Temperature Hot
— Temperature Max
— MotorTemp LOS Max Speed
— FAULT CHECKING......................... p. 54
— Driver1 Checks Enable
— Driver2 Checks Enable
— Driver3 Checks Enable
— Driver4 Checks Enable
— PD Checks Enable
— External Supply Max
— External Supply Min
— PWM FREQUENCY........................ p.54
DUAL DRIVE MENU ............ see Dual Drive
addendum,
Document number:
53097 DUAL-DRIVE
SUPPLEMENT_os31.
EM BRAKE CONTROL MENU..... p. 49
— Brake Type
— Pull In Voltage
— Holding Voltage
— Battery Voltage Comp.
— Set EM Brake On Fault
— Zero Speed Threshold
— Zero Speed Threshold Time
— Position Hold Settling Time
— Brake Set Time
— Torque Release Time
— Brake Release Time
— Torque Preload Time
— Torque Preload Enable
— Save Torque Preload
— Torque Preload Cancel Delay
— EM Brake Fault Motor Revs