EasyManuals Logo

CYBEX Treadmill User Manual

CYBEX Treadmill
107 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #23 background imageLoading...
Page #23 background image
Stopping the Treadmill
Press Stop once to pause your workout for 20 seconds (default setting) and to
enter the Workout Review. The belt will stop and the elevation will return to 0%,
but all workout settings and data will remain in memory for the pre-selected
time. Press the Quick Start key within 20 seconds to continue your workout at
the speed and elevation where you left off. If the Quick Start key has not been
pressed during the 20 second pause, workout data will be cleared and the
display will change to Dormant Mode.
Press Stop a second time to interrupt workout data from cycling and to change
the display to Dormant Mode.
The function of the immobilization
method: The purpose of immobilizing the
treadmill is to prevent unauthorized use. This
can be accomplished by removing the e-stop
key from the console, unclipping it from the
cord and putting it in a non-accessible place.
See Figure 2.
The emergency dismount: Follow the steps listed below if you experience
pain, feel faint or need to stop your treadmill in an emergency situation:
1. Grip handrails for support.
2. Step onto the top steps.
3. Pull the e-stop key off the console.
The function of the emergency stop: The e-stop
key functions as the emergency stop. In an
emergency situation, remove the e-stop key from
the console and the treadmill will come to a stop.
On the console, the e-stop location looks like Figure 3.
Safety Sentry
If you step off your treadmill during a workout, it may detect that you are not
there. After the pre-selected waiting period “run?” will appear in the center
window for a few seconds then Safety Sentry™ will stop the belt. If you press
Quick Start within the time selected you can resume your workout. NOTE: If
you are less than 100 lbs. and you are not using Polar the treadmill may not
detect you are there and cause the treadmill to come to a stop. Safety Sentry is
disabled above 11% grade. It can also be disabled by setting SAFE time to
“none”. If changes in elevation or speed occur while you are not there (such as
during a programmed workout) Safety Sentry resets its waiting period.
Cybex Pro Treadmill Owner’s & Service Manual
Page 3-5
Table of Contents . . . . . . . . . . . iii
1 Safety
Important Voltage Information . 1-1
Grounding Instructions . . . . . . . 1-1
Important Safety Instructions . . 1-2
Warning Decals. . . . . . . . . . . . . 1-4
Caution Decals . . . . . . . . . . . . . 1-7
Emergency Stop Key (e-stop). . 1-8
2 Technical Specifications
Specifications . . . . . . . . . . . . . . 2-1
3 Operation
Terms & Symbols Used . . . . . . 3-1
Quick Operation Guide . . . . . . 3-2
Detailed Operation Guide . . . . 3-2
Stopping the Treadmill . . . . . . . 3-5
Immobilization Method . . . . . 3-5
Emergency Dismount . . . . . . 3-5
Emergency Stop. . . . . . . . . . 3-5
Safety Sentry . . . . . . . . . . . . . . 3-5
Control During Operation . . . . . 3-6
Data Readouts . . . . . . . . . . . . . 3-6
Displaying Heart Rate . . . . . . . . 3-7
Heart Rate LED. . . . . . . . . . . . . 3-8
Use of Programs. . . . . . . . . . . . 3-8
Manual Mode . . . . . . . . . . . . . . 3-9
The Workout Profile . . . . . . . . 3-10
Meaning of % Grade . . . . . . . 3-10
5K Run . . . . . . . . . . . . . . . . . . 3-10
9 Holes . . . . . . . . . . . . . . . . . . 3-12
Heart Rate. . . . . . . . . . . . . . . . 3-14
Cardio . . . . . . . . . . . . . . . . . . . 3-16
Weight Loss . . . . . . . . . . . . . . 3-18
Manual . . . . . . . . . . . . . . . . . . 3-19
e-stop
+
-
Figure 3
Figure 2

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the CYBEX Treadmill and is the answer not in the manual?

CYBEX Treadmill Specifications

General IconGeneral
BrandCYBEX
ModelTreadmill
CategoryTreadmill
LanguageEnglish

Related product manuals