DAB ACTIVE DRIVER M/M 1.1 Instruction For Installation And Maintenance

ENGLISH
37
GENERAL INDEX page
1. GENERAL 39
2. WARNINGS 39
2.1 Skilled personnel 39
2.2 Safety 39
2.3 Responsibility 39
2.4 Particular warnings 39
3. APPLICATIONS 39
4. TECHNICAL DATA AND LIMITATIONS OF USE 39
5. ELECTRICAL CONNECTIONS OF THE A.D. TO THE ELECTROPUMP 40
6. CONNECTION TO THE POWER SUPPLY LINE 40
7. HYDRAULIC CONNECTIONS 41
7.4 Risk of frost 41
8. CHARACTERISTICS – INTERPRETATIONS – OPERATION 41
8.1 Characteristics and interpretations 42
8.2 Operation: keyboard factory settings 44
8.3 First switch-on operations (only with A.D. as accessory) 44
8.4 Operation: Parameters for the user (MODE and SET keys for 2 seconds) 45
8.4.1 SP: Setting the setpoint pressure (in bar) 45
8.5 Operation: Parameters for the installer (MODE and SET and - keys for 5 seconds) 45
8.5.1 rC: Setting the rated current of the electropump (excluding A.D. M/M 1.1) 45
8.5.2 rt: Setting the direction of rotation (excluding A.D. M/M 1.1) 45
8.5.3 Fn: Setting the rated frequency (pre-set value 50Hz) 45
8.5.4 od: Setting the operating mode of the A.D. 45
8.5.5 rP: Setting the fall in pressure for restarting 46
8.5.6 Ad: Setting the interconnection address (excluding A.D. M/M 1.1) 46
8.5.7 Eb: Enabling booster (pre-set value 2) (excluding A.D. M/M 1.1) 46
8.6 Operation: Technical Assistance displays and settings
(MODE and SET and + keys for 5 seconds)
46
8.6.1 tb: Setting the reaction time of the water lack blockage 46
8.6.2 GP: Setting the gain of the proportional coefficient of the PI 46
8.6.3 GI: Setting the gain of the integral coefficient of the PI 47
8.6.4 FS : Setting the maximum rotation frequency of the electropump. 47
8.6.5 FL : Setting the minimum frequency 47
8.6.6 Ft: Setting the low flow rate threshold 47
8.6.7 CM: Method of exchange (pre-set value 1) (excluding A.D. M/M 1.1) 47
8.6.8 AE : Enabling the anti-block/anti-frost function 48
8.6.9 Setting pump start 48
8.6.10 SF : Setting the starting frequency 48
8.6.11 St : Setting the starting time 48
8.6.12 Setup of the auxiliary digital inputs IN1; IN2; IN3 with the parameters i1; i2; i3
(excluding A.D. M/M 1.1 and A.D. M/T 1.0)
48
8.6.13 Active Driver M/T 2.2 = setting the set point P1 function of input 2 49
8.6.14 O1: setting output 1 function (active alarm)(excluding A.D. M/M 1.1 and A.D. M/T 1.0)
O2: setting output 2 function (pump operating)(excluding A.D. M/M 1.1 and A.D. M/T
1.0)
49
9. DISPLAYS 49
9.1 Displays of the main values (MODE key) 49
Fr: Display of the current rotation frequency (Hz) 49
UP: Display of pressure (in bar) 49
C1: Display of electropump phase current (A)
(excluding A.D. M/M 1.1 and A.D. M/T 1.0)
49
UE: Display of the version of the software with which the appliance is equipped 49
9.2 Monitor display (SET and - key for 2 seconds) 49
UF: Display of flow 49
ZF: Display of zero flow 49
FM: Display of the maximum rotation frequency (Hz) 49

DAB ACTIVE DRIVER M/M 1.1 Specifications

General

Brand	DAB
Model	ACTIVE DRIVER M/M 1.1
Category	Controller
Language	English