VLT
®
Series 3500
119
pulse start hand .................................................................. 76
pulses .................................................................................. 79
pumps.................................................................................. 69
Q
QUICK DISPLAY ............................................................... 100
Quick Setup data mode ..................................................... 49
Quick Setup menu .............................................................. 49
Quick Setup ........................................................... 47, 48, 52
quick-stop ......................................................... 70, 78, 79, 96
R
R (read) ................................................................................ 86
radio noise .......................................................................... 26
ramp down .......................................................................... 72
RAMP LOCAL ................................................................... 101
ramp selection .................................................................... 79
ramp time(s) .................................................................. 70, 79
RAMPING .......................................................................... 101
ramps................................................................................... 69
rated motor current ............................................................ 68
rated motor frequency ....................................................... 64
RDY+DC V OK ...............................................................82, 83
RDY+MOT+REM ...........................................................82, 83
READY+MOT.OK ...........................................................82, 83
REF FAULT ................................................................. 84, 102
REFERENCE % .......................................................... 94, 100
reference % ................................................................ 97, 100
reference Fault .................................................................. 102
reference for manual operation ......................................... 84
reference Locked .............................................................. 101
reference signal .................................................................. 64
relay 01 .......................................................................... 44, 71
relay 04 ................................................................................ 71
relay output ......................................................................... 32
relay output 01 ..............................................................75, 82
relay output 04 .................................................................... 82
remote control mode .................................................. 82, 101
remote Hand/Off/Auto ........................................................ 43
remote indication of motor speed ..................................... 36
remote indication of output current .................................. 38
remote mounting ................................................................ 45
remote operation ................................................................ 46
“Remote/Auto”............................................................ 46, 101
REMOTE/AUTO KEY .......................................................... 48
reset ............................................................................... 46, 76
reset and motor coasting stop .......................................... 78
reset key ............................................................................ 103
reset messages ................................................................ 103
resonance............................................................................ 70
RESTART ........................................................................... 103
return to factory defaults ................................................... 52
reverse ........................................................................... 36, 77
reverse direction ................................................................. 77
reversing.............................................................................. 67
RFI ................................................................................. 26, 33
row of dashes ..................................................................... 46
RUN HOURS ..................................................................... 100
RUN INV DISABL ................................................................ 99
RUN NORMAL ..................................................................... 99
RUN OK LOCAL ................................................................ 101
RUN OK. ............................................................................ 101
RUN@REF noWR ................................................... 81, 82, 83
RUNinRANGE ......................................................... 81, 82, 83
RUNNING ............................................................... 81, 82, 83
running above the frequency ............................................. 81
running below the frequency ............................................. 81
running hours ............................................................. 97, 100
RUNNING noWR .................................................... 81, 82, 83
running out of the current range ....................................... 81
running out of the frequency range ................................... 81
S
safety interlock(s) ......................................................... 35, 36
safety regulations ............................................................... 27
scale .................................................................................... 66
second line in display ......................................................... 46
selection of setup ............................................................... 76
serial bus ............................................................................. 93
serial communication ................................................... 34, 77
serial communication parameters ..................................... 93
serial interface .................................................................. 103
setpoint ............................................................................... 76
setup .................................................................................... 76
setups .................................................................................. 47
shield .............................................................................26, 27
shielded cable ..................................................................... 26
shielded motor cables ........................................................ 33
signal outputs ..................................................................... 75
sine shape ........................................................................... 69
sine
2
shape .......................................................................... 69
sine
3
shape .......................................................................... 69
software type ...................................................................... 98
software version ................................................................. 98
SPEED REF/SPEED = REF. ................................................ 90
speed reference ..................................................... 46, 76, 94
speed reference value ........................................................ 79
speed up and down ............................................................ 39
speed up/down .............................................................80, 84
STANDARD DISP .............................................................. 100
standard display ......................................................... 47, 100
start ............................................................................... 72, 77
start disabled .................................................................... 101
START ENABLED/NOT ENABLED ..................................... 90
“start forward” switch ........................................................ 77
start in reverse direction .................................................... 77
START INHIB. .................................................................... 101
START KEY .......................................................................... 48
start not possible ................................................................ 73
“start reverse” switch ......................................................... 77
start signal .......................................................................... 44
start-up test ...................................................................... 104
start/stop............................................................................. 77
starting current ................................................................... 72
starting into a rotating motor ............................................. 72
starting up ........................................................................... 46
static electricity ................................................................ 105
status messages ............................................................... 101
status word ................................................................... 89, 97
STOP ................................................................................... 84
stop.......................................................... 46, 76, 77, 78, 101
“Stop” ................................................................................ 101
STOP LOCAL .................................................................... 101
STOP REMOTE ................................................................. 101
“Stop/Reset” ....................................................................... 79
To Next Page
Loading...
Need help?
General