Danfoss VLT AutomationDrive FC 302

Other manuals for Danfoss VLT AutomationDrive FC 302

Service Guide370 pages

Operating Instructions122 pages

Installation Guide82 pages

Programming Guide722 pages

Installation Manual128 pages

Instruction Manual174 pages

Installation Instructions6 pages

Questions and Answers:

P
Patricia RiveraSep 18, 2025
How to fix earth fault in Danfoss VLT AutomationDrive FC 302 DC Drives?
- J
  James Hopkins PhDSep 18, 2025
  An earth fault in Danfoss DC Drives indicates current leakage from the output phases to earth, either in the cable between the frequency converter and the motor or in the motor itself. Remove power to the frequency converter and repair the earth fault. You can also check for earth faults in the motor by measuring the resistance to ground of the motor leads and the motor with a megohmmeter.
C
Candace CarlsonSep 18, 2025
What causes short circuit in Danfoss VLT AutomationDrive FC 302 DC Drives and how to fix it?
- J
  Jessica RamirezSep 22, 2025
  A short circuit in Danfoss DC Drives is caused by short-circuiting in the motor or motor wiring. To resolve this, remove power to the frequency converter and repair the short circuit.
M
Mary MontgomerySep 22, 2025
Why am I getting a mains phase loss error on my Danfoss VLT AutomationDrive FC 302?
- M
  Mary KellySep 22, 2025
  A mains phase loss error on your Danfoss DC Drives indicates that a phase is missing on the supply side, or the mains voltage imbalance is too high. Check the supply voltage and supply currents to the frequency converter.
A
Angelica SimonSep 22, 2025
What causes overload of digital output Terminal 27 in Danfoss DC Drives?
- M
  Michael LynnSep 22, 2025
  Overload of digital output Terminal 27 is caused by the load connected to terminal 27 or remove short-circuit connection. Check 5-00 Digital I/O Mode and 5-01 Terminal 27 Mode.
G
Garrett JohnsonSep 22, 2025
What causes overload of digital output Terminal 29 in Danfoss VLT AutomationDrive FC 302 DC Drives?
- R
  Richard CrawfordSep 22, 2025
  Overload of digital output Terminal 29 is caused by the load connected to terminal 29 or remove short-circuit connection. Check 5-00 Digital I/O Mode and 5-02 Terminal 29 Mode.
D
derekmooreSep 23, 2025
What to do if option configuration has changed in Danfoss VLT AutomationDrive FC 302 DC Drives?
- E
  ericmooreSep 23, 2025
  If the option configuration has changed in Danfoss DC Drives, it means one or more options have either been added or removed since the last power-down. Check that the configuration change is intentional and reset the unit.
J
Jennifer AdamsSep 23, 2025
How to troubleshoot heatsink temperature issues in Danfoss VLT AutomationDrive FC 302 DC Drives?
- P
  Paul BellSep 23, 2025
  If you're experiencing heatsink temperature issues with your Danfoss DC Drives, it means the maximum temperature of the heatsink has been exceeded. Check for conditions such as: * Ambient temperature being too high. * Motor cable being too long. * Incorrect airflow clearance above and below the frequency converter. * Blocked airflow around the frequency converter. * Damaged heatsink fan. * Dirty heatsink.
K
Kara KleinSep 23, 2025
What to do for DC overvoltage on Danfoss VLT AutomationDrive FC 302?
- A
  Adrienne Acevedo DVMSep 23, 2025
  To address DC overvoltage on Danfoss DC Drives, connect a brake resistor and extend the ramp time.
J
Justin TranSep 23, 2025
How do I resolve a control word timeout on Danfoss VLT AutomationDrive FC 302 DC Drives?
- D
  Danielle HernandezSep 23, 2025
  A control word timeout on Danfoss DC Drives indicates a lack of communication to the frequency converter. Check connections on the serial communication cable, increase 8-03 Control Word Timeout Time, and check the operation of the communication equipment.
J
Jennifer BishopSep 23, 2025
What causes motor thermistor over temp in Danfoss VLT AutomationDrive FC 302 DC Drives?
- M
  munozseanSep 23, 2025
  A motor thermistor over temp error in Danfoss DC Drives can be caused by several factors. Check for motor overheating and if the motor is mechanically overloaded. When using terminal 53 or 54, check that the thermistor is connected correctly between either terminal 53 or 54 (analog voltage input) and terminal 50 (+10 V supply). Also check that the terminal switch for 53 or 54 is set for voltage. When using digital inputs 18 or 19, check that the thermistor is connected correctly between either terminal 18 or 19 (digital input PNP only) and terminal 50. Check 1-93 Thermistor Source selects terminal 18 or 19.

Danfoss VLT AutomationDrive FC 302 Specifications

General

Category	DC Drives
Control Method	Flux Vector Control
Communication Options	CANopen, PROFIBUS
Cooling	Forced convection
Enclosure	IP20, IP21, IP55, IP66
Protection Class/Rating	IP20
Protection Features	Overvoltage, Undervoltage, Overcurrent, Overtemperature, Short Circuit
Approvals	CE, UL, cUL
Ambient Temperature	-10°C to +50°C
Storage Temperature	-40°C to +70°C
Relative Humidity	5% to 95% (non-condensing)
Output Voltage	0 V to Input Voltage