Why does Danfoss VLT HVAC Drive FC 102 motor run rough?
If the motor runs rough with your Danfoss DC Drives, it could be due to overmagnetization. Check the motor settings in parameter groups 1-2* Motor Data, 1-3* Addl. Motor Data, and 1-5* Load Indep. Setting.
Why is motor speed unstable in Danfoss VLT HVAC Drive FC 102 DC Drives?
If the motor speed is unstable in your Danfoss DC Drives, it might be due to incorrect parameter settings. Review the settings in parameter group 1-6* Load Depen. Setting. For closed-loop operation, check settings in parameter group 20-0* Feedback.
Why Danfoss DC Drives motor will not brake?
If the motor will not brake in your Danfoss DC Drives, review the brake parameters and ensure they are correctly configured. Also, check if the ramp-down times are too short.
How to fix a short circuit in Danfoss VLT HVAC Drive FC 102 DC Drives?
If your Danfoss DC Drives indicate a short circuit, it means there is short-circuiting in the motor or motor wiring. Remove the power to the frequency converter and repair the short circuit.
What causes line power current imbalance greater than 3% in Danfoss DC Drives?
If you notice a line power current imbalance greater than 3% in your Danfoss DC Drives, it could be a problem with the line power supply itself. Check the line power supply. If the imbalance remains on the same input terminal, there may be a problem with the unit, and you should contact the supplier.
How to deal with torque limit issues in Danfoss VLT HVAC Drive FC 102 DC Drives?
To manage torque limit issues in Danfoss DC Drives, if the motor torque limit is exceeded during ramp up, extend the ramp up time. If the generator torque limit is exceeded during ramp down, extend the ramp down time. If torque limit occurs while running, possibly increase the torque limit, ensuring the system can operate safely at a higher torque. Also, check the application for excessive current draw on the motor.
What to do for an inrush fault in Danfoss DC Drives?
If your Danfoss DC Drives are showing an inrush fault, it means too many power-ups have occurred within a short time period. Let the unit cool to operating temperature.
What causes 24 V Supply Low warning on Danfoss VLT HVAC Drive FC 102?
If your Danfoss DC Drives unit is showing a '24 V Supply Low' warning, it indicates that the supply on the power card is out of range. To fix this, check for a defective power card.
How to troubleshoot a dark or non-functional display on Danfoss VLT HVAC Drive FC 102?
If your Danfoss DC Drives display is completely dark or has no function, start by checking the input power source. Also, inspect the fuses or circuit breaker and replace if necessary. If the LCP isn't getting power, replace the faulty LCP or connection cable. Ensure there are no shorts on the control voltage terminals and that you're using the correct LCP model. Finally, adjust the contrast or, if the display is still defective, replace it. If the internal voltage supply is faulty, contact your supplier.
Why won't the motor brake with Danfoss VLT HVAC Drive FC 102 DC Drives?
If the motor will not brake using Danfoss DC Drives, check parameter group 2-0* DC Brake and 3-0* Reference Limits for possible incorrect settings in the brake parameters or ramp down times that are too short.
General| Enclosure | IP20, IP21, IP55 |
|---|---|
| Ambient Temperature Range | -10°C to +40°C |
| Storage Temperature Range | -25°C to +70°C |
| Relative Humidity | 5-95% (non-condensing) |
| Communication Protocols | Modbus RTU, BACnet, Profibus |
| Certifications | CE, UL, cUL |
| Control Principle | PWM |
| Cooling Method | Forced air cooling |
| Input Voltage | 200-240V, 380-480V, 525-600V |
| Control Modes | sensorless vector control, closed loop vector control |
To Next Page