How to resolve CANopen PDO is read-only and write-protected in Delta ASD-A2-3023?
To resolve CANopen PDO is read-only and write-protected in Delta Servo Drives, when the specified object in the message is write- protected, use NMT: Reset node or 0x6040.Fault Reset.
How to resolve CANopen PDO is not allowed in PDO in Delta ASD-A2-3023 Servo Drives?
To resolve CANopen PDO is not allowed in PDO in Delta Servo Drives, when the specified object in the message does not support PDO, use NMT: Reset node or 0x6040.Fault Reset.
How to fix Parameter group of PR#8 is out of range in Delta Servo Drives?
To fix parameter group of PR#8 is out of range in Delta Servo Drives, when the parameter group of command source exceeds the range, use DI.Alm Reset or write 0 into P0-01.
How to fix The parameter number of PR#8 is out of range in Delta Servo Drives?
To fix the parameter number of PR#8 is out of range in Delta Servo Drives, when the parameter number of command source exceeds the range, use DI.Alm Reset or write 0 into P0-01.
How to fix An error occurs when writing parameter via PR exceeds the range in Delta Servo Drives?
To fix an error occurs when writing parameter via PR exceeds the range in Delta Servo Drives, when an error occurs when writing parameters, use DI.Alm Reset or P0-01 = 0.
How to resolve CANopen PDO is write-protected when Servo On in Delta ASD-A2-3023?
To resolve CANopen PDO is write-protected when Servo On in Delta Servo Drives, when the specified object in the message is write- protected when Servo ON, use NMT: Reset node or 0x6040.Fault Reset.
How to resolve Error occurs when reading CANopen PDO via EEPROM in Delta ASD-A2-3023 Servo Drives?
To resolve error occurs when reading CANopen PDO via EEPROM in Delta Servo Drives, when an error occurs when loading the default value via ROM at start-up, use NMT: Reset node or 0x6040.Fault Reset.
How to resolve Error occurs when writing CANopen PDO via EEPROM in Delta ASD-A2-3023?
To resolve error occurs when writing CANopen PDO via EEPROM in Delta Servo Drives, when an error occurs when saving the current value into ROM, use NMT: Reset node or 0x6040.Fault Reset.
How to resolve The accessing address of EEPROM is out of range when using CANopen PDO in Delta ASD-A2-3023?
To resolve the accessing address of EEPROM is out of range when using CANopen PDO in Delta Servo Drives, when the quantity of the data inside ROM is over the planned space, use NMT: Reset node or 0x6040.Fault Reset.
How to resolve CRC of EEPROM calculation error occurs when using CANopen PDO in Delta ASD-A2-3023?
To resolve CRC of EEPROM calculation error occurs when using CANopen PDO in Delta Servo Drives, when it indicates that the data stored in ROM has been damaged, use NMT: Reset node or 0x6040.Fault Reset.
General| Control Modes | Position, Speed, Torque |
|---|---|
| Protection Class | IP20 |
| Series | A2 |
| Type | Servo Drive |
| Communication Interface | RS-485, CANopen |
| Protection Features | Overvoltage, Undervoltage, Overcurrent, Overtemperature, Short Circuit |
| Ambient Temperature | 0°C to 45°C |
| Storage Temperature | -20 ~ 65°C |
| Humidity | 20 ~ 90% RH, non-condensing |
Provides essential safety guidelines for handling and operating the servo drive.
Outlines routine maintenance and inspection procedures for the servo drive.
Crucial initial checks for product verification and damage assessment before installation.
Details on matching servo drives with their corresponding servo motors for system configuration.
Critical environmental requirements for the servo drive and motor during installation.
Detailed wiring instructions for 220V series servo drives and peripheral devices.
Detailed wiring instructions for 400V series servo drives and peripheral devices.
Step-by-step guide for setting parameters via the servo drive's panel.
Procedure for inspecting the servo motor and drive without load before operation.
Instructions for safely applying power to the servo drive and motor.
Comprehensive guide on tuning the servo system for optimal performance.
A comprehensive list of all servo drive parameters with their functions and related sections.
Configuration settings for RS-485 and RS-232 communication parameters.
Lists common alarms for the servo drive, their descriptions, and corresponding actions.
Detailed table of common causes and corrective actions for servo drive alarms.
Provides specific corrective actions for various alarm codes after they occur.
Technical specifications for the ASDA-A2 series servo drives.
Technical specifications for the ECMA series servo motors.
Instructions for installing absolute encoder systems, including connection examples.
Steps for initializing and operating absolute systems.
Checks to be performed before applying power to the servo drive.
To Next Page
