Why is my Delta Servo Drives showing a reverse limit error?
A reverse limit error on your Delta Servo Drives can occur because: * The reverse limit switch is activated: Enable the reverse limit switch. * The servo system is unstable: Re-adjust the parameter or evaluate the motor capacity.
What does 'Forward Limit Error' mean on Delta ASD-A2-3023 Servo Drives?
A forward limit error on Delta Servo Drives indicates: * The forward limit switch is activated: Enable the forward limit switch. * The servo system is unstable: Re-adjust the parameter or evaluate the motor capacity.
What to do if Delta ASD-A2-3023 show The internal of the encoder is in error?
If your Delta Servo Drives are showing that the internal of the encoder is in error: * The internal of the encoder is in error. (The internal memory and the internal counter are in error): If issue persists, please send the drive back to the distributors or contact with Delta. * When power on, the motor operates because of mechanical inertia or other causes: When power on, please make sure the motor shaft stands still and will not operate.
What causes abnormal EEPROM in Delta ASD-A2-3023 Servo Drives?
If your Delta Servo Drives are showing an abnormal EEPROM: * It is in error when DSP accesses EEPROM: The fault occurs when applying to the power. It means one of the parameters is over the reasonable range. Please re-power on after adjusting. The fault occurs in normal operation. It means it is in error when writing the parameter. The alarm can be cleared by DI.ARST. * Abnormal hidden parameter: Please set the correct type of the drive. * Data in ROM is damaged: Please send the drive back to the distributors or contact with Delta.
What causes Abnormal Signal Output in Delta ASD-A2-3023?
If your Delta Servo Drives are showing abnormal signal output: * The encoder is in error and cause the abnormal signal output: Conduct the corrective actions of AL.011, AL.024, AL.025, AL.026. * The output pulse exceeds the hardware allowable range: Correctly set parameter P1-76 and P1-46.
How to troubleshoot serial communication error in Delta ASD-A2-3023 Servo Drives?
If you're experiencing a serial communication error with your Delta Servo Drives, check the following: * Improper setting of the communication parameter: Correctly set the parameter value. * Incorrect communication address: Correctly set the communication address. * Incorrect communication value: Correctly set the value.
What to do if Delta ASD-A2-3023 Servo Drives show Encoder voltage error or the internal of the encoder is in error?
If your Delta Servo Drives are showing encoder voltage error or the internal of the encoder is in error: * Battery voltage is too high: According to the procedure of Over voltage to check. When corrective actions are done, AL.028 will be cleared automatically. * The internal encoder is in error: If the situation is not improving, please send the drive back to the distributors or contact with Delta.
What causes serial communication time out in Delta Servo Drives?
A serial communication timeout error in Delta Servo Drives can occur due to: * Improper setting of the time-out parameter: Correctly set the value. * The drive hasn’t received the communication command for a long time: Correct wiring.
What does main circuit power lack phase mean for Delta ASD-A2-3023?
If your Delta Servo Drives are showing main circuit power lack phase, the main circuit power is abnormal. Make sure it applies to the power. If issue persists, please send the drive back to the distributors or contact with Delta.
How to fix incorrect wiring of the motor power line U, V, W in Delta Servo Drives?
If your Delta Servo Drives are showing incorrect wiring of the motor power line U, V, W because the wiring of U, V, W of the motor is incorrectly connected or the connection is breakdown, follow the user manual to correctly wire U, V, and W and make sure it is grounded.
General| Control Modes | Position, Speed, Torque |
|---|---|
| Protection Class | IP20 |
| Series | A2 |
| Type | Servo Drive |
| Communication Interface | RS-485, CANopen |
| Protection Features | Overvoltage, Undervoltage, Overcurrent, Overtemperature, Short Circuit |
| Ambient Temperature | 0°C to 45°C |
| Storage Temperature | -20 ~ 65°C |
| Humidity | 20 ~ 90% RH, non-condensing |
Provides essential safety guidelines for handling and operating the servo drive.
Outlines routine maintenance and inspection procedures for the servo drive.
Crucial initial checks for product verification and damage assessment before installation.
Details on matching servo drives with their corresponding servo motors for system configuration.
Critical environmental requirements for the servo drive and motor during installation.
Detailed wiring instructions for 220V series servo drives and peripheral devices.
Detailed wiring instructions for 400V series servo drives and peripheral devices.
Step-by-step guide for setting parameters via the servo drive's panel.
Procedure for inspecting the servo motor and drive without load before operation.
Instructions for safely applying power to the servo drive and motor.
Comprehensive guide on tuning the servo system for optimal performance.
A comprehensive list of all servo drive parameters with their functions and related sections.
Configuration settings for RS-485 and RS-232 communication parameters.
Lists common alarms for the servo drive, their descriptions, and corresponding actions.
Detailed table of common causes and corrective actions for servo drive alarms.
Provides specific corrective actions for various alarm codes after they occur.
Technical specifications for the ASDA-A2 series servo drives.
Technical specifications for the ECMA series servo motors.
Instructions for installing absolute encoder systems, including connection examples.
Steps for initializing and operating absolute systems.
Checks to be performed before applying power to the servo drive.
To Next Page
