What does 'F20: Efficiency Abnormal' mean on my Delta H2.5?
The 'F20: Efficiency Abnormal' error on your Delta Inverter indicates that the efficiency is not as expected. This could be because the calibration is incorrect, so check the accuracy of current and power. It may also be caused by current feedback circuit being defective, so check the current feedback circuit inside the inverter.
What should I do if my Delta H2.5 Inverter displays 'F35: HW Bus OVR'?
If your Delta Inverter shows a 'F35: HW Bus OVR' error, it could be due to several reasons. You should check the driver circuit for boost inside the inverter, or the Voc of PV array is over 510Vdc (H2.5) or 560Vdc (H3/ H3A/ H4A) - in this case, modify the solar array setting, and make the Voc less than 500Vdc (H2.5) or 550Vdc (H3/ H3A/ H4A). Another reason could be a defective detection circuit inside the inverter, or a surge during operation.
What does 'E11: OVR' mean on my Delta H2.5 and how can I fix it?
The 'E11: OVR' error on your Delta Inverter indicates an over-voltage condition. This may be due to the actual utility voltage being higher than the OVR setting. You can measure the utility AC voltage at the inverter terminal to confirm this. It can also be caused by an incorrect country or Grid setting, which you should check, or a detection circuit malfunction inside the inverter.
What does 'E10: UVR' mean on my Delta Inverter and how to fix it?
The 'E10: UVR' error on your Delta Inverter indicates an under-voltage condition. This could be because the actual utility voltage is higher than the UVR setting, so measure the utility AC voltage to the inverter terminal. It might also be due to an incorrect country or Grid setting, which you should verify. Finally, a detection circuit malfunction inside the inverter could be the cause.
What does 'F23: Comm. Fault (Dis.)' mean on my Delta H2.5 Inverter?
The 'F23: Comm. Fault (Dis.)' error on your Delta Inverter indicates a communication fault. This may be because DSP is idling, so check reset and crystal in DSP. It could also be caused by the communication connection being disconnected, so check the connection between DSP and COMM. Another possible reason is the communication circuit malfunction, so check the communication circuit.
What does 'F56: HW incompat.' mean on my Delta Inverter?
The 'F56: HW incompat.' error on your Delta Inverter indicates a hardware incompatibility. This means that HW power rating is incorrect, so check comm. HW power rating info.
What does 'F42: CT sensor Fail (A)' mean on my Delta Inverter?
The 'F42: CT sensor Fail (A)' error on your Delta Inverter indicates a failure with the CT sensor. This might be due to Inverter choke Fail, so check Inverter choke inductance. It could also be caused by Output Filter Fail, so check output filter capacitance. Another possible reason is detection circuit malfunction inside the inverter.
What does 'F06: NTC0 Circuit Fail' mean on my Delta H2.5 Inverter?
The 'F06: NTC0 Circuit Fail' error on your Delta Inverter indicates a failure in the NTC0 circuit. This may be because the ambient temperature is greater than 100? or less than -40?. Check the installation ambient temperature and environment. It could also be caused by a detection circuit malfunction inside the inverter.
What does 'F24: RCMU Over Rating' mean on my Delta Inverter and how to fix it?
The 'F24: RCMU Over Rating' error on your Delta Inverter indicates that the RCMU is over its rating. This can be caused by a PV array insulation fault, so check the insulation of Solar inputs. It may also be due to large PV array capacitance between Plus to Ground or Minus to Ground, so check the capacitance (+ GND & - GND), it must be less than 2.5uF, and install an external transformer if necessary. Another cause can be either side of boost driver or boost choke malfunction, so check boost driver & boost choke. A final possibility is a detection circuit malfunction inside the inverter.
What does error 'E34: Insulation' mean on my Delta H2.5 Inverter?
The error 'E34: Insulation' on your Delta Inverter indicates an insulation issue. This could be due to a PV array insulation fault, so check the insulation of Solar inputs. It may also be caused by large PV array capacitance between Plus to Ground or Minus to Ground or both, so check the capacitance and dry PV panel if necessary. A final possibility is a detection circuit malfunction inside the inverter.
To Next Page
General
