What to do if my Delta RPI-M20A Inverter shows 'No Grid'?
If your Delta Inverter displays a 'No Grid' error, it could be due to the AC breaker being off. In this case, switch on the AC breaker. Alternatively, there might be a disconnection in the AC plug. Ensure the AC plug is correctly connected to the inverter.
What causes 'Ground Current' error on Delta RPI-M20A?
A 'Ground Current' error on a Delta Inverter may arise from several factors: a PV array insulation fault, so check the insulation of Solar inputs. It could also be due to large PV array capacitance between Plus to Ground or Minus to Ground, so check the capacitance (+ GND & - GND), and it must be less than 2.5uF. Install a external transformer if necessary. Additionally, either side of the boost driver or boost choke might malfunction, so check boost driver & boost choke. Finally, a detection circuit malfunction could be the cause; in that case, check the detection circuit inside the inverter.
What to do if my Delta Inverter shows 'HW Con. Fail'?
If your Delta Inverter displays 'HW Con. Fail', it may be due to a wrong connection in the AC plug. Check the AC connection, ensuring it accords to the manual. Alternatively, a detection circuit malfunction could be the cause, so check the detection circuit inside the inverter.
What to do if Delta Inverter displays 'HW FAN' error?
If your Delta Inverter is displaying a 'HW FAN' error, consider the following: 1. One or more fans might be locked; remove any object stuck in the fan(s). 2. One or more fans could be defective; replace the defective fan(s). 3. One or more fans might be disconnected; check the connections of all fans. 4. A detection circuit malfunction could be the cause; check the detection circuit inside the inverter.
What does 'SPD Fail' mean on my Delta RPI-M20A and how to fix it?
An 'SPD Fail' error on your Delta Inverter can indicate several issues: 1. The inverter was struck by lighting, check inverter’s status. 2. One or more SPDs are defective, replace the defective SPD. 3. One or more SPDs are disconnected, check the connections of SPDs. 4. A detection circuit malfunction, check the detection circuit inside the inverter.
What could cause a 'Temperature Low' error on my Delta RPI-M20A?
A 'Temperature Low' error on your Delta Inverter might be triggered if the ambient temperature is below -30 degrees. Check the installation ambient and environment. Additionally, a detection circuit malfunction could be the cause, so check the detection circuit inside the inverter (RTM1, RTB1, RTG1 and RTH1).
What does 'HW NTC1 Fail' mean on my Delta RPI-M20A Inverter?
The 'HW NTC1 Fail' error on your Delta Inverter can be triggered if the ambient temperature is above 90 degrees or below -30 degrees. Check the installation ambient and environment. It may also indicate a detection circuit malfunction, so check the detection circuit inside the inverter (RTM1).
What does 'HW NTC2 Fail' mean on my Delta RPI-M20A?
If your Delta Inverter is showing a 'HW NTC2 Fail' error, it may indicate that the ambient temperature is above 90 degrees or below -30 degrees. Check the installation ambient and environment. Another possible cause is a detection circuit malfunction, so check the detection circuit inside the inverter (RTB1).
What does 'HW NTC3 Fail' indicate on my Delta RPI-M20A Inverter?
A 'HW NTC3 Fail' error on your Delta Inverter may indicate that the ambient temperature is above 90 degrees or below -30 degrees. You should check the installation ambient and environment. It could also be due to a detection circuit malfunction, so check the detection circuit inside the inverter (RTG1).
What does 'HW NTC4 Fail' mean on my Delta RPI-M20A?
A 'HW NTC4 Fail' error on your Delta Inverter could be due to the ambient temperature being above 90 degrees or below -30 degrees. Check the installation ambient and environment. It may also indicate a detection circuit malfunction, so check the detection circuit inside the inverter (RTH1).
Outlines important safety instructions, including cautions, warnings, and danger notices.
Provides explanation and procedures for installing, operating, maintaining, and troubleshooting solar inverters.
Describes the 3-phase grid-tied solar inverter and its operation illustration.
Provides information on where to find more product details online.
Details the unpacking procedure for the RPI-M15A / M20A inverter.
Instructs users to check for damage and verify all included accessories.
Explains how to identify the inverter's model and specifications from its label.
Illustrates the inverter's exterior components and input/output interfaces.
Details the steps for securely mounting the inverter onto a wall using brackets and screws.
Provides recommended installation orientation, clearance requirements, and environmental considerations.
Covers precautions and checks before commencing any wiring tasks.
Explains the procedures and requirements for connecting the inverter to the AC grid.
Details how to connect the DC input from the PV array to the inverter.
Describes how to connect communication modules for data transfer and control.
Explains the pin definitions and connection methods for RS-485 communication.
Details the connections for Emergency Power Off and Dry Contact features.
Explains the inverter's LCD display and LED indicators for status.
Guides the user through the initial setup and configuration process.
Describes the main display screen showing output power, status, and energy data.
Details how to view AC and DC voltage, current, and power readings.
Explains how to access historical energy generation data on yearly, monthly, and daily bases.
Describes how to view recorded error and fault events.
Explains how to view historical maximum and minimum operating data.
Lists information such as serial number, firmware version, and inverter ID.
Introduces the section for adjusting various inverter functions and parameters.
Allows adjustment of language, date, time, screen saver, and display contrast.
Enables setting CO2 saving, earning value, and communication baud rates.
Covers advanced settings for installers, including ID, insulation, and country configurations.
Introduces functions for controlling active and reactive power output based on regulations.
Explains how to keep the inverter connected to the grid during voltage dips as per regulations.
Provides instructions on how to clean the inverter's fans.
Details the procedure for replacing a faulty fan unit.
Explains how to clean the air inlet and outlet filters.
Outlines the procedures for safely removing the inverter from operation for maintenance or storage.
Details screw torque specifications for fan and air inlet components.
Provides details on AC wire, AC plug, rubber rings, MC4 wire, and communication module assembly.
To Next Page
General
