Denon AVC-3000 - Page 3

11.
_ 12.
8A.
IMPORTANT SAFEGUARDS
Read Instructions — All the safety and operating instructions should
be read before the appliance is operated.
Retain Instructions — The safety and operating instructions should be
retained for future reference.
Heed Warnings — All warnings on the appliance and in the operating
instructions should be adhered to.
Follow Instructions — All operating and use instructions should be
followed.
Cleaning — Unplug this video product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
Attachments — Do not use attachments not recommended by the
video product manufacturer as they may cause hazards.
Water and Moisture — Do not use this video product near water — for
example, near a bath tub, wash bowl, kitchen sink, or laundry tub, ina
wet basement, or near a swimming pool, and the like.
Accessories — Do not place this video product on an unstable cart,
stand, tripod, bracket, or table. The video product may fall, causing
serious injury to a child or adult, and serious damage to the
appliance. Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with the video product.
Any mounting of the appliance should follow the manufacturer's
instructions, and should use a mounting accessory recommended by
the manufacturer.
An appliance and cart
combination should be
moved with care.
Quick stops, excessive
force, and uneven
surfaces may cause the
appliance and cart
combination to overturn.
Ventilation — Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the video product and
to protect it from overheating, and these openings must not be
blocked or covered. The openings should never be blocked by placing
the video product on a bed, sofa, rug or other similar surface. This
video product should never be placed near or over a radiator or heat
register. This video product should not be placed in a built-in
installation such as a bookcase or rack unless proper ventilation is
provided or the manufacturer's instructions have been adhered to.
Power Sources — This video product should be operated only from the
type of power source indicated on the marking label. If you are not
sure of the type of power supply to your home, consult your
appliance dealer or local power company. For video products
intended to operate from battery power, or other sources, refer to the
operating instructions.
Grounding or Polarization — This video product is equipped with a
polarized alternating-current line plug (a plug having one blade wider
than the other). This plug will fit into the power outlet only one way.
This is a safety feature. If you are unable to insert the plug fully into
the outlet, try reversing the plug. If the plug should still fail to fit,
contact your electrician to replace your obsolete outlet. Do not defeat
the safety purpose of the polarized plug.
Power-Cord Protection - Power-Supply cords should be routed so
that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit from the
appliance.
FIGURE A
EXAMPLE OF ANTENNA GROUNDING ACCORDING
TO NATIONAL ELECTRICAL CODE INSTRUCTIONS
CONTAINED IN ARTICLE 810 —- “RADIO AND
TELEVISION EQUIPMENT”
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
Protective Attachment Plug — The appliance is equipped with an
attachment plug having overload protection. This is a safety feature.
See Instruction Manual for replacement or resetting of protective
device. If replacement of the plug is.required,.be sure the service
technician has used a replacement plug specified by the manufactur-
er that has the same overload protection as the original plug.
Outdoor Antenna Grounding — If an outside antenna or cable system
is connected to the video product, be sure the antenna or cable
system is grounded so as to provide some protection against voltage
surges and built-up static charges. Section 810 of the National
Electrical Code, ANSI/NFPA No. 70-1984, provides information with
respect to proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna-discharge unit, connec-
tion to grounding electrodes, and requirements for the grounding
electrode. See Figure A.
Lightning — For added protection for this video product receiver
during a lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and disconnect the
antenna or cable system. This will prevent damage to the video
product due to lightning and power-line surges.
Power Lines — An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or power
circuits, or where it can fall into such power lines or circuits. When
installing an outside antenna system, extreme care should be taken to
keep from touching such power lines or circuits as contact with them
might be fatal.
Overloading — Do not overload wall outlets and extension cords as
this can result in a risk of fire or electric shock.
Object and Liquid Entry — Never push objects of any kind into this
video product through openings as they may touch dangerous
voltage points or short-out parts that could result in a fire or electric
shock. Never spill liquid of any kind on the video product.
Servicing — Do not attempt to service this video product yourself as
opening or removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service personnel.
Damage Requiring Service — Unplug this video product from the wall
outlet and refer servicing to qualified service personnel under the
following conditions:
a.When the power-supply cord or plug is damaged.
b.lf liquid has been spilled, or objects have fallen into the video
product.
c.lf the video product has been exposed to rain or water.
d.lf the video product does not operate normally by following the
operating instructions. Adjust only those controls that are covered
by the operating instructions as an improper adjustment of other
controls may result in damage and will often require extensive work
by a qualified technician to restore the video product to its normal
operation.
e.lf the video product has been dropped or the cabinet has been
damaged.
f. When the video product exhibits a distinct change in performance —
this indicates a need for service.
Replacement Parts - When replacement parts are required, be sure
the service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock or other
hazards.
Safety Check — Upon completion of any service or repairs to this video
product, ask the service technician to perform safety checks to
determine that the video product is in proper operating condition.
AVC-3000/3000G
HE
»s INSULATORS?
wast
ANTENN A
Erbe ead LEADAN WIRE
ENTAANCE
eQuueMeNT
ANTENNA.
‘DISCHARGE
uate
‘TO EXTERNAL ANTENNA
TERMINALS OF PRODUCT
POWER BERVICE GROUNDIN'
ELECTRODE svaTeM .
{0g.
mntarioe
metal
water
pipet
‘GROUND
WIRES:
~ GROUND CLAMPS
BONDING JUMPERt
OPTIONAL ANTENNA GROUNDING ELECTRODE
ORIVEN 8 FEET {2.64 m) INTO THE
IF REQUIRED BY LOCAL CODES. ‘Scene
sz08 SECTION B10 ~ 21Uf1,
Fig. 4
Use No. 10 AWG (5.3 mm?) copper, No. 8 AWG (8.4 mm?)
aluminum, No. 17 AWG (1.0 mm?) copper-clad steel or
bronze wire, or larger, as a ground wire.
Secure antenna lead-in and ground wires to house with
stand-off insulators spaced from 4-6 feet (1.22—1.83 m)
apart.
Mount antenna discharge unit as close as possible to
where lead-in enters house.
Use jumper wire not smaller than No. 6 AWG (13.3 mm?)
copper, or the equivalent, when a separate antenna-
mone: electrode is used. See NEC Section 810-21 (j).