Denon AVR-1000 - Listening to the Radio; Tuning and Storing Radio Stations

LISTENING TO THE RADIO
B Tuning
ERX, oS
Main unit Remote control unit
2. Select the reception band.
——
Main unit
FM There is a change as shown at the left,
| and indication @ inside the MFD
AM changes.
3. Select the tuning mode.
AUTO
The mode switches as shown at the left.
When the suto mode is set, “AUTO”
lights on the MFD @.
MANUAL
Set the auto mode for automatic tuning, the manual
mode for manual tuning.
4. Tune in the station.
Main unit
In the manuai tuning mode:
Press the UP button once to increase the frequency by
one step, the DOWN button once to decrease the
frequency by one step.
The frequency changes continuously when the but-
tons are held in.
The “TUNED” indicator @ tights on the MFD when a
station is tuned in.
in the auto tuning mode:
When the UP or DOWN button is pressed, automatic
searching begins, and searching stops when a station
is tuned in,
NOTES:
e When in the auto tuning mode on the FM band, the “STEREO” indicator @ fights on the MFD when a stereo broadcast is tuned in. At
‘|
'
Ht)
o1of OF
[i
f OOF O
i OHO* C8
040-{0: D: 0:10 jo
ai
olla}
MED display
M
rae
—_
TUNED
o ® ® ®
open frequencies, the noise is muted and the “TUNED” @ and “STEREO” @ indicators turn off.
« When the manual tuning mode is set, FM stereo broadcasts are received in monaural and the “STEREO” indicator @ turns off.
@ Storing stations at the preset buttons
1. Follow steps 1 to 4 under “Tuning” to tune in a station.
2. Press the MEMORY button.
—— The “CH” @indicator on the MFD
Ose, flashes.
Main unit
3. Select the oreset channels.
Boal
Cy
The channels switch as shown at the
left, and the MFD display © also
changes.
When “A” is displayed, preset channels
1 to 8 can be preset, and when “B” is
displayed, preset channels 9 to 16 can
be preset.
4. Press the preset number that you want to store to
memory.
[1-9 | 2-10 | 311 4-12 | 5-13 |] 6-14 | 7-15 | 8-16
Ke
@ Recalling stations with the preset buttons
First store stations at the preset buttons using the above
procedure.
[1] Using the buttons on the main unit
Main unit
1. Press the SHIFT button to select the preset channels.
wr
Main unit
Preset channels 1 to 8 can be recalled when “A” is
displayed, preset channels 9 to 16 when “B” is dis-
played.
2. Press the button for the station you want to recall.
(2j Using the buttons on the remote control unit
Main unit
3. Press the PRESET 4 and 7 buttons.
TUNER
a
ey
Remote control unit Remote contro! unit
A-1 B- 16
4 4
A-8 8-93
t I
8-9 A-8
4 4
B- 16 A-1
PRESET
?
Sy
The preset channel switches as shown above.
Er 2
7 10800 =
NOTES:
The preset memory standby mode is set for 6 seconds when
the MEMORY button is pressed. When the MEMORY and
SHIFT buttons are pressed, the preset memory standby mode
is prolonged for 6 seconds. The preset memory standby mode
turns off after 6 seconds.
The preset memory standby mode is cancelled if any button
other than preset buttons 1 to 8 (9 to 16), the MEMORY button
or the SHIFT button is pressed.
13