Getting Started Connections Playback Remote ControlMulti-zone Information Troubleshooting Specifications
ENGLISH
See overleaf
Making Detailed Settings (Manual Setup)
Setting items Setting contents
EQ Customize
Set so that unused equalizer
settings are not displayed
when MULTEQ is pressed.
Equalizer settings for which
“Not Used” is set with the
Quick Select function cannot
be stored and called out.
Audyssey Byp. L/R : Set when not using the “Audyssey Byp L/R”
equalizer.
Used : Use.
Not Used : Do not use.
Set so that “Audyssey Byp. L/R” settings can be made when
Audyssey™ Auto Setup procedure is performed.
•
•
Audyssey Flat : Set when not using the “Audyssey Flat” equalizer.
Used : Use.
Not Used : Do not use.
Set so that “Audyssey Flat” settings can be made when Audyssey™
Auto Setup procedure is performed.
•
•
Manual : Set when not using the “Manual” equalizer.
Used : Use.
Not Used : Do not use.
•
•
Setting items Setting contents
Network Connecting
(Continued)
q On the GUI menu, select “Network Connecting” – “Detail” and
press ENTER.
w Use o p to set “DHCP” to “OFF”, then press i.
The DHCP function is disabled.
e Use uip to input the address and press ENTER.
IP Address
: Set the IP address within the ranges shown below.
The Network Audio function cannot be used if other IP addresses
are set.
CLASS A: 10.0.0.0 ~ 10.255.255.255
CLASS B: 172.16.0.0 ~ 172.31.255.255
CLASS C: 192.168.0.0 ~ 192.168.255.255
Subnet Mask : When connecting an xDSL modem or terminal
adapter directly to the AVR-3310, input the subnet mask indicated
in the documentation supplied by your provider. Normally input
255.255.255.0.
Default Gateway : When connected to a gateway (router), input
its IP address.
Primary DNS, Secondary DNS : If there is only one DNS address
indicated in the documentation supplied by your provider, input it
at “Primary DNS”. If there are two or more DNS addresses, input
the first one at “Secondary DNS”.
r Use i to select “Exit” and press ENTER.
Setup is complete.
When connecting to the network via a Proxy server, select “Proxy” and
press ENTER (vpage 38 “Proxy settings”).
If you are using a broadband router (DHCP function), there is no need
to make the settings at “IP Address” and “Proxy”, since the DHCP
function is set to “ON” in the AVR-3310’s default settings.
If the AVR-3310 is being used connected to a network without the
DHCP function, the network settings must be made. In this case, some
knowledge of networks is required. For details, consult a network
administrator.
If you cannot connect to the Internet, recheck the connections and
settings (vpage 22).
If you do not understand about Internet connection, contact your ISP
(Internet Service Provider) or the store from which you purchased your
computer.
When you want to cancel the setting during IP address input, press
RETURN.
•
•
•
•
b
•
•
•
•
•
Main remote control
operation buttons
:Displaying the menu
Cancel the menu
:Moves the cursor
(Up/Down/Left/Right)
:Confirm the setting :Return to previous menu
Make network settings.
Setting items Setting contents
Network Connecting
Make settings for wired
LAN.
1. Connect the LAN cable (vpage 22 “Connecting to a Home Network
(LAN)”).
2. Turn on the AVR-3310 (vpage 23 “Turning the Power On”).
AVR-3310 performs automatic network setup due to the DHCP
function.
When connecting to a network that has no DHCP function, perform the
setting in step 3.
3. Set the IP address at the “Network Connecting”.
q
r
e
Making the Network Settings (Network Setup)
Default settings are underlined.
w
Settings
To Next Page
Loading...
Need help?
General
Weight and Dimensions
