Denon AVR-S910W

TECHNICAL SPECIFICATIONS FOR AVR-X2200W
n
Audio section
• Power amplier
Rated output :
Front :
95 W + 95 W ( 8 Ω, 20 Hz - 20 kHz with 0.08 % T.H.D.)
125 W + 125 W ( 6 Ω, 1 kHz with 0.7 % T.H.D.)
Center :
95 W ( 8 Ω, 20 Hz - 20 kHz with 0.08 % T.H.D.)
125 W ( 6 Ω, 1 kHz with 0.7 % T.H.D.)
Surround :
95 W + 95 W ( 8 Ω, 20 Hz - 20 kHz with 0.08 % T.H.D.)
125 W + 125 W ( 6 Ω, 1 kHz with 0.7 % T.H.D.)
Surround back :
95 W + 95 W ( 8 Ω, 20 Hz - 20 kHz with 0.08 % T.H.D.)
125 W + 125 W ( 6 Ω, 1 kHz with 0.7 % T.H.D.)
Output connectors : 4 - 16 Ω
n
Analog section
Input sensitivity/Input impedance : 200 mV / 47 kΩ
Frequency response : 10 Hz - 100 kHz — +1, -3 dB (Direct mode)
S/N ratio : 100 dB (IHF-A, Direct mode)
n
Video section
• Color component video connector
Input/output level and impedance :
Y signal — 1 Vp-p, 75 Ω
PB / CB signal — 0.7 Vp-p, 75 Ω
PR / CR signal — 0.7 Vp-p, 75 Ω
Frequency response : 5 Hz - 60 MHz — 0, –3 dB
n
Tuner section
(Note : μV at 75 Ω, 0 dBf = 1 x 10
–15
W)
Reception frequency range : FM 87.5 MHz - 107.9 MHz (for E3)
FM 87.5 MHz - 108.0 MHz (for E2, E1C)
FM 76.0 MHz - 95.0 MHz (for JP)
AM 520 kHz - 1710 kHz (for E3)
AM 522 kHz - 1611 kHz (for E2, E1C)
AM 522 kHz - 1629 kHz (for JP)
Effective sensitivity : FM 1.2 μV (12.8 dBf) (for E3)
FM 1.2 μV (12.8 dBf) (for E2, E1C, JP)
AM 18 μV (for E3)
AM 18 μV (for E2, E1C, JP)
50 dB sensitivity :
  MONO―2.8μV(20.2dBf)
S/N ratio (IHF-A) : MONO ― 70 dB (for E3)
MONO ― 78 dB (for E2, E1C, JP)
STEREO ― 67 dB (for E3)
STEREO ― 67 dB (for E2, E1C, JP)
Distortion : MONO ― 0.7 % (for E3)
MONO ― 0.7 % (1 kHz) (for E2, E1C, JP)
SRETEO ― 1.0 % (for E3)
SRETEO ― 1.0 % (1 kHz) (for E2, E1C, JP)
n
Wireless LAN section
Network type (wireless LAN standard) : Conforming to IEEE 802.11b
Conforming to IEEE 802.11g
Conforming to IEEE 802.11n
(Wi-Fi® compliant)z1
Security : WEP 64 bit, WEP 128 bit
WPA/WPA2-PSK (AES)
WPA/WPA2-PSK (TKIP)
Radio frequency :
2.4 GHz
No. of channels : 1 - 11 ch (for E3)
1 - 13 ch (for E2, E1C, JP)
z
1 The Wi-Fi® CERTIFIED Logo and the Wi-Fi CERTIFIED On-Product Logo
are registered trademarks of the Wi-Fi Alliance.
n
Bluetooth section
Communications system : Bluetooth Version 2.1 + EDR
(Enhanced Data Rate)
Transmission power : Maximum 2.5 mW (Class 2)
Maximum communication range : Approx. 32.8 ft/10 m in line of sight
Frequency band : 2.4 GHz band
Modulation scheme : FHSS (Frequency-Hopping Spread Spectrum)
Supported proles :
A2DP (Advanced Audio Distribution Prole)1.2
AVRCP (Audio Video Remote Control Prole)1.4
Corresponding codec : SBC, AAC
Transmission range (A2DP) :
20Hz-20,000Hz
z2 The actual communication range varies depending on the inuence of
such factors as obstructions between devices, electromagnetic waves
from microwave ovens, static electricity, cordless phones, reception
sensitivity, antenna performance, operating system, application
software etc.
n
General
Power supply : (for E3) : AC 120 V, 60 Hz
(for E2) : AC 230 V, 50 Hz / 60 Hz
(for E1C) : AC 220 V, 50 Hz
(for JP) : AC 100 V, 50 Hz / 60 Hz
Power consumption : 500 W
Power consumption in standby mode : 0.1 W
Power consumption in CEC standby mode : 0.5 W
Power consumption in network standby mode : 2.7 W
For purposes of improvement, specications and design are subject to
change without notice.
9