Denon AVR-X3000 Service Manual

Error
Code
Details of Error code Display Coping strategies
13
BlockErase failed before rewriting
Main.
E r a s e f a i l 1 3
This unit automatically retries several times.
Wait until the FL display stops.
If the FL display stops at the Error display,
press and hold the "Power operation (
X
)"
button for ve seconds.
14
BlockWrite failed while rewriting
Main.
U p d a t i n g f a i l 1 4
This unit automatically retries several times.
Wait until the FL display stops.
If the FL display stops at the Error display,
press and hold the "Power operation (
X
)"
button for ve seconds.
15
Error in Verify after rewriting Main
(CheckSumError).
U p d a t e C h e c k N G 1 5
This unit automatically retries several times.
Wait until the FL display stops.
If the FL display stops at the Error display,
press and hold the "Power operation (
X
)"
button for ve seconds.
20
Unable to detect USB after
SBLMode.
C o n n e c t i o n F a i l 2 0
Disconnect and connect the USB memory.
21
No FirmwareFile in USB after
SBLMode.
F i l e s N o t F o u n d 2 1
Disconnect and connect the USB memory.
22
FirmwareFile in USB after
SBLMode for unsupported Model
name/area
N o t M a t c h F i r m 2 2
Check the supported Model name/area for
the FirmwareFile.
23
Failed to obtain entire Firmware
information after SBLMode.
C o n n e c t i o n F a i l 2 3
Disconnect and connect the USB memory.
24
TimeOut while obtaining entire
Firmware information after
SBLMode
C o n n e c t i o n F a i l 2 4
This unit automatically retries several times.
Wait until the FL display stops.
If the FL display stops at the Error display,
press and hold the "Power operation (
X
)"
button for ve seconds.
25 Failed to transit to SBLMode.
C o n n e c t i o n F a i l 2 5
This unit automatically retries several times.
Wait until the FL display stops.
If the FL display stops at the Error display,
press and hold the "Power operation (
X
)"
button for ve seconds.
26
TimeOut in Download (writing to
SDRAM) for FirmwareDownload
D o w n l o a d f a i l 2 6
This unit automatically retries several times.
Wait until the FL display stops.
If the FL display stops at the Error display,
press and hold the "Power operation (
X
)"
button for ve seconds.
27
Failed to write to EEPROM after
SBLMode.
C o n n e c t i o n F a i l 2 7
This unit automatically retries several times.
Wait until the FL display stops.
If the FL display stops at the Error display,
press and hold the "Power operation (
X
)"
button for ve seconds.
36 Unable to detect USB.
C o n n e c t i o n F a i l 3 6
This unit automatically retries several times.
Wait until the FL display stops.
If the FL display stops at the Error display,
press and hold the POWER button for ve
seconds.
37 No FirmwareFile in USB.
F i l e s N o t F o u n d 3 7
This unit automatically retries several times.
Wait until the FL display stops.
If the FL display stops at the Error display,
press and hold the "Power operation (
X
)"
button for ve seconds.
38
FirmwareFile in USB for
unsupported Model name/area
N o t M a t c h F i r m 3 8
This unit automatically retries several times.
Wait until the FL display stops.
If the FL display stops at the Error display,
press and hold the "Power operation (
X
)"
button for ve seconds.
39 TimeOut in USBCheck
C o n n e c t i o n F a i l 3 9
This unit automatically retries several times.
Wait until the FL display stops.
If the FL display stops at the Error display,
press and hold the "Power operation (
X
)"
button for ve seconds.
3A
Unable to detect USB for
FirmwareDownload.
C o n n e c t i o n F a i l 3 A
This unit automatically retries several times.
Wait until the FL display stops.
If the FL display stops at the Error display,
press and hold the "Power operation (
X
)"
button for ve seconds.
76

Denon AVR-X3000 Specifications

General

Receiver type	Surround
Frequency range	10 - 100000 Hz
Output impedance	16 Ω
Input sensitivity	200 mV
Pre-out connectivity	Yes
Audio output channels	7.1 channels
Signal-to-Noise Ratio (SNR)	102 dB
Total Harmonic Distortion (THD)	0.08 %
Power output per channel (1KHz@6 Ohm)	135 W
Power output per channel (20-20KHz@8 Ohm)	105 W
HDMI in	7
Audio (L/R) in	5
Composite video in	3
Ethernet LAN (RJ-45) ports	1
Component video (YPbPr/YCbCr) in	2
Connectivity technology	Wired
Speakers connectivity type	Banana connector
Audio formats supported	AAC, FLAC, MP3, WAV, WMA
Image formats supported	JPG
Wi-Fi	No
RDS features	PTY, TP
AM band range	520 - 1710 kHz
FM band range	87.5 - 108 MHz
Supported radio bands	AM, FM
Internet radio services supported	Spotify, vTuner
Supported video modes	1080i, 1080p, 480p, 576p, 720p
Display	VFL
Color depth	24 bit
Aspect ratio	4:3, 16:9
Product color	Black
Audio decoders	DTS Neo:X, Dolby Digital, Dolby Digital EX, Dolby Digital Plus, Dolby Pro Logic II, Dolby Pro Logic IIx, Dolby Pro Logic IIz, Dolby TrueHD, DTS, DTS-ES (Discrete 6.1), DTS-ES (Matrix 6.1), DTS-HD, DTS-HD Master Audio
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Apple docking compatibility	iPhone, iPod
AC input voltage	230 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.1 W
Power consumption (typical)	600 W
Cables included	AC

Weight and Dimensions

Depth	379 mm
Width	434 mm
Height	167 mm
Weight	10700 g