Denon DRA-275RD - Troubleshooting Guide; Problem Resolution

NGLISH
®
TUNING PRESET (Preset station buttons)
These buttons are used for storing stations or recalling stations which
have been preset. Using the SHIFT/PTY button you can preset a total of
40 FM or AM stations into preset channels.
Once a radio has been memorized, the same station can later be tuned
in instantly simply by recalling the corresponding preset channel with
PRESET UP or DOWN button.
DISPLAY
9eee8¢e0e8 8
RDS indicator
This lights when receiving RDS broadcasts, and flashes during the RDS
search operations.
EON indicator
This lights when receiving EON information.
TA (Traffic Announcement) indicator
This lights when receiving traffic announcements.
TP (Traffic Programme) indicator
This flashes during the TP search operation and lights when TP stations
are tuned in.
RT indicator
This lights when the RT (Radio Text) button is pressed.
PTY indicator
This flashes during the PTY (Programme type) search operation.
TUNED indicator
This lights when a station is properly tuned in.
STEREO indicator
This lights when receiving stereo broadcasts. It remains off when receiv-
ing AM broadcasts.
REAR PANEL
Oo
2]
FM ANT (FM antenna terminals)
75-Q/ohms coaxial cable can be connected to this terminal. For antenna
connecting procedure, refer to page 9 and 10.
AM ANT (AM antenna terminals)
Connect the attached AM loop antenna. (Refer to page 9 and 10 for con-
nections).
GND (Grounding terminal)
The grounding wire of the turntable is connected here.
e@ Hum or noise may be generated if the grounding wire is not con-
nected.
PHONO (Phono input terminals)
The output cord of the turntable is connected here.
Since the input sensitivity of “PHONO” is extremely high, do not use the
unit without the input pin cord. If used without this cord, the speakers may
generate hum.
CD
The output cord of the CD player is connected here.
VIDEO
The audio outputs of VIDEO equipment, such as a VCR or Video Disc may
be connected here.
TAPE-1, TAPE-2/VCR (Tape deck playback /record-
ing terminal)
Two tape decks or tape deck and VCR can be connected to these jacks for
full-fledged playback, recording and tape dubbing operation.
SPEAKER SYSTEMS (Speaker terminals)
Two pairs of speakers A and B can be connected to these terminals.
8
SHIFT / PTY button
Use this button to select the memory blocks, A (1 to 8), B (1 to 8), C (1 to
8), D (1 to 8) or E (1 to 8).
For PTY search, use this button to select the program type.
When writing station names, use this button to set the writing position.
AUTO indicator
This indicates the tuning mode. It lights in the auto mode, and remains off
in the manual mode.
MEMO indicator
This indicator lights for approximately 10 seconds when the MEMORY
button has been pressed anda station can be stored ona PRESET CHAN-
NEL button.
This flashes continuously during the auto memory operation.
CH indicator
This lights when the preset channel number and shift mode (A, B, C, D or
E) are displayed.
TAPE-1 / TAPE-2 indicator
The TAPE~1 indicator lights when the TAPE-1 source is selected with the
tape selector buttons. The TAPE-2 indicator lights when the TAPE-2/VCR
source is selected.
Multi function display
This displays the frequency, station name, programme type, etc.
AC OUTLET (AC power outlets)
This AC outlet is controlled by the power switch. Maximum capacity is
100 W.
AC CORD (Power cord)
Connect this cord into the wail outlet.
VIDEO (Video input / output terminals)
As a full-featured AV center, this receiver makes possible comection of
a TV monitor, VCR and/or a video disc player (Video) to thesejacks.
@® Simulcast monitor
Select the desired audio source after selecting VIDEO fuiction. You
can monitor the selected audio source with the picture fron the VID-
EO input.
@ VCR monitor
When the TAPE-2/VCR is selected, you can only monitorthe sound
and picture from the TAPE-2/VCR input.
Even you select the audio source after selecting TAPE-i/ VCR, the
sound and picture remains TAPE-2/VCR.
@® Simulcast copy
If you select the audio source after selecting VIDEO functin, you can
record the selected audio and picture from VIDEO input into VCR.
CAUTION
Protective Circuit
This set is equipped with a high speed protective circuit. This circit pro-
tects the internal circuitry from damage due to large currents fowving
when the speaker jacks are not completely connected or when an iu tput
is generated by a short circuit.
This protective circuit's operation cuts off the output to the speakir s. In
such a case, be sure to turn the power to the set off and check thy con-
nections to the speakers. Then turn the power on again. After mutig for
several seconds, the set will operate normally.