EasyManua.ls Logo

Dexter Laundry B Series - User Manual

Dexter Laundry B Series
32 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
8514-265-001 REV C PAGE 1
INDUSTRIAL DRYER
MODEL T-20X2 AND T-30X2 ON-PREMISE
B-SERIES CONTROL, ELECTRIC-HEATED
OPERATOR’S MANUAL
INSTALLATION & OPERATION INSTRUCTIONS
The dryer must not be stored or installed where it will be exposed to water and/or weather and is
suitable for use in room temperatures between 40F and 105F (5C and 45C.)
Post the following “For Your Safety” caution in a prominent location:
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any
other appliance or machine.
It is important that you read this Manual and retain it for future reference. For service or
replacement parts, contact the Dexter Distributor in your area or the manufacturer.
WARNING / Avertissement
WARNING– Risk of Fire / Avertissement: Risque d’incendie
Clothes dryer installation must be performed by a qualified installer. / L’installation de la
sécheuse doit être effectuée par un spécialiste qualifié.
Install the clothes dryer according to the manufacturer’s instructions and local codes.
Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type)
duct is installed, use duct that has been investigated and found acceptable for use with clothes
dryers. Flexible venting materials are known to collapse, be easily crushed, and trap lint.
These conditions will obstruct clothes dryer airflow and increase the risk of fire. / Ne pas
installer une sécheuse avec des matériaux de ventilation en plastique. Dans le cas où un
conduit en métal flexible (du genre à feuille) est installé, il doit être d’un type spécifique
identifié par le fabricant de l’appareil comme acceptable pour les sécheuses. Les matériaux de
ventilation flexibles sont réputés pour s’aplatir, se déformer facilement et collecter de la
peluche. Ces conditions vont obstruer l’écoulement d’air de la sécheuse et augmenter le risque
d’incendie.
To reduce the risk of severe injury or death, follow all installation instructions. / Pour réduire le
risque de blessures graves ou mortelles, suivre toutes les instructions d’installation.
Save these instructions. / Garder les instructions.
Dexter Laundry, Inc.
2211 West Grimes Avenue
Fairfield, Iowa 52556

Other manuals for Dexter Laundry B Series

Questions and Answers

  • M
    Miss Samantha KramerSep 12, 2025
    What to do if my Dexter Laundry Dryer displays 'TEMP SENSOR SHORT'?
    • S
      Sandra HeathSep 12, 2025
      If your Dexter Laundry Dryer displays 'TEMP SENSOR SHORT', inspect the temperature probe wires. Ohm test the temperature probe; it should read 10K Ohms at room temperature.
  • C
    Chris HamiltonSep 9, 2025
    What does 'Close Door' mean on my Dexter Laundry B Series?
    • V
      veronicahansenSep 9, 2025
      The 'Close Door' message on your Dexter Laundry Dryer indicates that either the loading door or the lint compartment door circuit is not closed. Inspect the door switches and wiring. Also, check the lint door paddle to ensure it fully engages the lint door switch.
  • N
    Nicholas FrancisSep 8, 2025
    How to troubleshoot a 'Drive Overcurrent' error on my Dexter Laundry B Series?
    • M
      Michael ClarkSep 8, 2025
      To troubleshoot a 'Drive Overcurrent' error on your Dexter Laundry Dryer: 1. Check that the dryer cylinder turns freely by hand. If it doesn't, remove the belt and see if the motor turns freely. If the motor doesn't turn freely, replace it. Check for obstructions in the cylinder or check the bearings. 2. Check the motor wires for a short circuit. Separate and insulate any touching conductors; splice broken wires or replace the motor. 3. Check braking resistors to ensure they measure the correct resistance. Replace any resistors that don't measure properly.
  • J
    jasmine14Sep 7, 2025
    What to do if my Dexter Laundry B Series Dryer shows a 'Brown Out' error?
    • V
      vschultzSep 7, 2025
      If your Dexter Laundry Dryer displays a 'Brown Out' error, test the incoming power to ensure the transformer is on the correct tap. Inspect the control board, and visually check resistor R185. If the resistor appears burnt, replace the control board after correcting the voltage issue to the machine.
  • D
    David CrawfordAug 23, 2025
    Why is my Dexter Laundry Dryer taking so long to dry?
    • S
      stephanie37Aug 23, 2025
      Several factors can cause slow drying. Make sure the correct temperature setting is selected. Clean the lint screen. Ensure there are no air flow restrictions and that make-up air adheres to installation guidelines. Also, check the exhaust for any obstructions, following the installation guidelines.
  • K
    Kurt GilmoreSep 5, 2025
    Why does my Dexter Laundry Dryer say 'Operation in Progress'?
    • E
      Erica PowellSep 5, 2025
      The 'Operation in Progress' message on your Dexter Laundry Dryer indicates that the current drying cycle hasn't finished. The error will automatically disappear once the operation is complete.
  • A
    Andrea MartinezSep 4, 2025
    What to do if the Dexter Laundry B Series tumbler turns, but there is no burner flame?
    • L
      Lynn Williams MDSep 4, 2025
      If the tumbler of your Dexter Laundry Dryer turns, but there is no burner flame, check the following: * Ensure the gas shut-off valve is in the open position. * Follow the procedure for checking the ignition cycle listed in Dryer Ignition section of this manual.
  • M
    michaeltannerSep 3, 2025
    How to fix a Dexter Laundry B Series when the tumbler does not turn?
    • J
      Jane GrimesSep 3, 2025
      If the tumbler on your Dexter Laundry Dryer isn't turning, there are a few things you can check: * Make sure the loading door is completely closed. * Ensure the lint compartment door is also completely closed. * Inspect the drive belts for wear and replace them if needed. If these steps don't resolve the issue, it could be a Variable Frequency Drive Fault, and you should contact a Dexter agent for assistance.
  • D
    David OrozcoSep 2, 2025
    Why is my Dexter Laundry Dryer drying so slowly?
    • R
      Robert WalkerSep 2, 2025
      If your Dexter Laundry Dryer is drying clothes slowly, there might be several reasons: * Ensure the correct temperature setting is selected. * Clean the lint screen. * Check for any obstructions in the exhaust and follow the installation guidelines. * Adhere to the installation guidelines for static back pressure and make-up air to resolve airflow restrictions.
  • D
    Donald AllenAug 31, 2025
    What to do if Dexter Laundry B Series displays 'Temp Sensor Short' or 'Temp Sensor Open'?
    • A
      acarsonSep 1, 2025
      If the control displays a 'Temp Sensor Short' or 'Temp Sensor Open' error code, press the programming button to clear the error code. If the error code persists, contact a Dexter agent for assistance.

Dexter Laundry B Series Specifications

General IconGeneral
BrandDexter Laundry
ModelB Series
CategoryDryer
LanguageEnglish

Related product manuals