Dexter Laundry B Series - User Manual

32 pages

Save Page as PDF

To Next Page

8514-265-001 REV C PAGE 1

INDUSTRIAL DRYER

MODEL T-20X2 AND T-30X2 ON-PREMISE

B-SERIES CONTROL, ELECTRIC-HEATED

OPERATOR’S MANUAL

INSTALLATION & OPERATION INSTRUCTIONS

The dryer must not be stored or installed where it will be exposed to water and/or weather and is

suitable for use in room temperatures between 40F and 105F (5C and 45C.)

Post the following “For Your Safety” caution in a prominent location:

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any

other appliance or machine.

It is important that you read this Manual and retain it for future reference. For service or

replacement parts, contact the Dexter Distributor in your area or the manufacturer.

WARNING / Avertissement

WARNING– Risk of Fire / Avertissement: Risque d’incendie

Clothes dryer installation must be performed by a qualified installer. / L’installation de la

sécheuse doit être effectuée par un spécialiste qualifié.

Install the clothes dryer according to the manufacturer’s instructions and local codes.

Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type)

duct is installed, use duct that has been investigated and found acceptable for use with clothes

dryers. Flexible venting materials are known to collapse, be easily crushed, and trap lint.

These conditions will obstruct clothes dryer airflow and increase the risk of fire. / Ne pas

installer une sécheuse avec des matériaux de ventilation en plastique. Dans le cas où un

conduit en métal flexible (du genre à feuille) est installé, il doit être d’un type spécifique

identifié par le fabricant de l’appareil comme acceptable pour les sécheuses. Les matériaux de

ventilation flexibles sont réputés pour s’aplatir, se déformer facilement et collecter de la

peluche. Ces conditions vont obstruer l’écoulement d’air de la sécheuse et augmenter le risque

d’incendie.

To reduce the risk of severe injury or death, follow all installation instructions. / Pour réduire le

risque de blessures graves ou mortelles, suivre toutes les instructions d’installation.

Save these instructions. / Garder les instructions.

Dexter Laundry, Inc.

2211 West Grimes Avenue

Fairfield, Iowa 52556

Main Page

Other manuals for Dexter Laundry B Series

Original Instructions31 pages

Operator's Manual24 pages

Questions and Answers

B
Brian SmithAug 30, 2025
What to do if Dexter Laundry B Series Dryer tumbler turns, but there is no burner flame?
- C
  Cynthia CookeAug 30, 2025
  If the tumbler turns but there's no burner flame, first, make sure the gas shut-off valve is in the open position. Then, follow the procedure for checking the ignition cycle listed in the Dryer Ignition section of this manual.
T
Tanya GillAug 29, 2025
What to do if Dexter Laundry Dryer displays 'PCB Error' or 'Comm Error'?
- B
  Brenda WoodsAug 29, 2025
  If the control displays a 'PCB Error' or 'Comm Error' code, try cycling the power to the dryer to clear the error code. If the error persists, contact a Dexter Agent for assistance.
D
dweberAug 28, 2025
What to do if Dexter Laundry Dryer tumbler does not turn?
- J
  John PrinceAug 28, 2025
  If the tumbler isn't turning, first, ensure the control display shows drying time available; if not, add money as needed. Next, verify that the loading door and the lint compartment door are completely closed. Check the drive belts for excessive wear and replace them if necessary. If a Variable Frequency Drive Fault is displayed, contact a Dexter agent for assistance.
J
Joan SmithAug 27, 2025
Why is my Dexter Laundry B Series slow drying?
- L
  Linda GoodmanAug 27, 2025
  Several factors can cause slow drying. Check that the correct temperature setting is selected. Clean the lint screen. Ensure there are no air flow restrictions and that make-up air follows installation guidelines. Also, inspect the exhaust for obstructions and ensure it adheres to installation guidelines.
M
Michelle WhiteAug 27, 2025
Why Dexter Laundry B Series tumbler turns, but there is no burner flame?
- J
  Jeffrey VillarrealAug 27, 2025
  First, check that the gas shut-off valve is in the open position. If the issue continues, follow the procedure for checking the ignition cycle listed in the Dryer Ignition section of this manual.
D
Dr. Lisa RivasAug 25, 2025
What does “Temp Sensor Short” or “Temp Sensor Open” error mean on Dexter Laundry B Series Dryer?
- L
  Lawrence TaylorAug 26, 2025
  If the display shows a “Temp Sensor Short” or “Temp Sensor Open” error code, it relates to the temperature sensor. Press the programming button to clear the error code. If the error continues, contact a Dexter agent for help.
C
christopher84Aug 25, 2025
What does “PCB Error” or “Comm Error” code mean on my Dexter Laundry Dryer?
- A
  allisonlopezAug 25, 2025
  If you see a “PCB Error” or “Comm Error” code, it indicates a control error. Try turning the dryer off and then on again to clear the code. If the error persists, contact a Dexter Agent for assistance.