Why my Dexter Laundry T-900 tumbles in one direction?
If your Dexter Laundry Washer tumbles in only one direction, remove the inspection cover at the rear and record any numbers or letters displayed. Refer to the fault code section for more information. Also, inspect the yellow enable wires from the main relay PCB and at the VFD.
What to do if water comes in but level does not rise in Dexter Laundry T-900 Washer?
If water comes in but the level doesn't rise in your Dexter Laundry Washer, check the drain valve for blockages, and inspect the drain valve motor and gear train. If there is power but the drain valve does not close, replace the valve. Check for power to the drain valve; if there's no power, check the (brn/yel) circuit for power. Also, check the black and white wires at the molex plug on the main PCB controller and at the main relay PCB.
Why no cold water to tub in wash for Dexter Laundry T-900 Washer?
If cold water isn't entering the tub during the wash cycle of your Dexter Laundry Washer, start by checking the water valve coil for continuity at its terminals; replace it if there's no continuity. Next, inspect the water inlet screens for blockages and clean them if necessary. Ensure that the water supply is turned on and operating correctly. Check the black or white wires at the Molex plug on the PCB at the main controller and at the relay PCB. Lastly, test the pressure switch for continuity between terminal contacts; if there's no continuity, check the pressure switch hose for obstructions, and replace the switch if the hose is clear.
What to do if the water level is too high in my Dexter Laundry Washer?
If the water level is too high in your Dexter Laundry Washer, check for blockage in the pressure switch hose. Also, check for the pressure switch opening circuit across terminals. Replace the switch if the contacts do not open.
Why Dexter Laundry Washer machine does not turn?
To troubleshoot why your Dexter Laundry Washer isn't turning, begin by checking the VFD (Variable Frequency Drive). Remove the inspection panel and note any numbers or letters displayed. If there's no display, turn off the power to the machine at the breaker for two minutes, then turn it back on to reset. If the issue persists and there's still no display, consider replacing the VFD.
Why Dexter Laundry Washer water drains slowly?
If water is draining slowly from your Dexter Laundry Washer, inspect the hoses and drain valve for any blockages. Ensure the drain size is adequate. If necessary, check the building drains for blockages.
What to do if water level is too high in Dexter Laundry Washer?
If the water level in your Dexter Laundry Washer is too high, the issue is likely with the pressure switch. Start by checking the pressure switch hose for any blockages. Then, check if the pressure switch is opening the circuit across its terminals. If the contacts do not open, it's time to replace the switch.
What causes water drains slowly in Dexter Laundry T-900 Washer?
If water drains slowly from your Dexter Laundry Washer, check the hoses and drain valve for blockage and clean if necessary. Also, check the building drains for blockage or inadequate size.
Why water does not flush softener compartment of Dexter Laundry T-900 Washer?
If water does not flush the softener compartment of your Dexter Laundry Washer, check to ensure that the water valve is operating. If not, check for 120VAC to the water valve from the Input/Output PCB. If there is 120VAC, change the water valve. If there is no voltage check the Input/Output PCB. Also, check all screens for obstructions and clean them. Ensure that the water is turned on and operating.
What causes water comes in but level does not rise in Dexter Laundry T-900?
If water comes into your Dexter Laundry Washer but the level does not rise, check the drain valve for blockage and the drain valve motor and gear train. If there is power but the drain valve does not close, replace the valve. Check for power to the drain valve; if there's no power, check the (brown/yellow) circuit for power. Also, check or replace the water valve diaphragms.
Crucial safety information covering personnel, installation, operation, and hazards.
Details on shock, cut, burn, explosion, fire, and other specific hazards.
Safety advice for maintenance, repair, and troubleshooting procedures.
Defines warning, danger, informative, and reminder symbols used in the manual.
Details model identification, washer characteristics, and technical terms.
Comprehensive technical data for various washer models.
Guidance on mounting, anchoring, plumbing, and electrical setup.
Steps for starting, running, programming, and using the washer.
Routine upkeep, fault diagnosis, and repair guidance.
Details on installation parts, common service parts, and fuses.
Information on the WEEE symbol and proper product disposal.
Certifications and declarations regarding product standards.
General| Brand | Dexter Laundry |
|---|---|
| Model | T-900 |
| Category | Washer |
| Language | English |
To Next Page