EasyManua.ls Logo

Dexter Laundry T-900 - User Manual

Dexter Laundry T-900
340 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
1
8514-300-001 REV PR
Original Instrucons
Please read this informaon and retain for reference.
Dexter Laundry, Inc.
2211 West Grimes Avenue
Fairfield, Iowa 52556 - USA
OPERATOR’S MANUAL
INSTALLATION & OPERATION INSTRUCTIONS
FOR COMMERCIAL WASHERS

Table of Contents

Other manuals for Dexter Laundry T-900

Preview: Parts & Service Manual
Parts & Service Manual77 pages
Preview: Service Manual
Service Manual116 pages
Preview: Operator's Manual
Operator's Manual68 pages
Preview: Service Procedures And Parts Data
Service Procedures And Parts Data110 pages

Questions and Answers

  • F
    fmuellerSep 1, 2025
    Why no cold water to tub in wash for Dexter Laundry T-900 Washer?
    • B
      briansuttonSep 1, 2025
      If cold water isn't entering the tub during the wash cycle of your Dexter Laundry Washer, start by checking the water valve coil for continuity at its terminals; replace it if there's no continuity. Next, inspect the water inlet screens for blockages and clean them if necessary. Ensure that the water supply is turned on and operating correctly. Check the black or white wires at the Molex plug on the PCB at the main controller and at the relay PCB. Lastly, test the pressure switch for continuity between terminal contacts; if there's no continuity, check the pressure switch hose for obstructions, and replace the switch if the hose is clear.
  • F
    farrellmelissaSep 23, 2025
    What to do if the door will not open on Dexter Laundry Washer/Dryer?
    • R
      Robin MurraySep 23, 2025
      If the door on your Dexter Laundry Washer/Dryer won't open, check if the thermoactuator(s) and its mechanism are stuck or binding, preventing the door lock solenoid from opening. Ensure the locking thermoactuator isn't receiving 120VAC during the last 1 1/2 minutes of the cycle and that the unlocking thermoactuator is receiving 120VAC during the last minute. If the thermoactuators don't receive voltage at the correct times, change the timer. If the timing and voltage are correct, replace the thermoactuator.
  • D
    Debra MitchellSep 1, 2025
    Why my Dexter Laundry T-900 tumbles in one direction?
    • A
      Andrea CampbellSep 1, 2025
      If your Dexter Laundry Washer tumbles in only one direction, remove the inspection cover at the rear and record any numbers or letters displayed. Refer to the fault code section for more information. Also, inspect the yellow enable wires from the main relay PCB and at the VFD.
  • M
    Mark FlemingSep 2, 2025
    How to fix water level too high in Dexter Laundry Washer?
    • J
      Jill MarshallSep 2, 2025
      If the water level is too high in your Dexter Laundry Washer, check for blockages in the pressure switch hose. Also, check for the pressure switch opening circuit across the terminals and replace the switch if the contacts do not open.
  • D
    David MorrowSep 2, 2025
    Why my Dexter Laundry T-900 Washer does not spin?
    • D
      Diane WrightSep 2, 2025
      If your Dexter Laundry Washer does not spin, check the pressure switch for continuity across terminals #21 & #22, which indicates that the pressure switch has reset to the empty position. If there is no continuity, replace the pressure switch.
  • Q
    qclementsNov 24, 2025
    Why my Dexter Laundry T-900 tumbles in only one direction?
    • J
      Justin PopeNov 24, 2025
      If your Dexter Laundry Washer tumbles in only one direction, check the blue and orange wires on the variable frequency drive for alternating 0V to 24 VDC for forward and reverse direction from the Input/Output PCB. Also, check wire connections at the drive. If there's no voltage, check the Input/Output PCB for alternating or Input/Output PCB red output lights for forward #13 and reverse #14. If no red output lights illuminated, check the single red light on the CPU board. If the CPU tests okay, change Ribbon Cables between CPU and Input/Output PCB. If the forward #13 and reverse #14 output lights on the Input/Output PCB are illuminated, check to ensure that 0VDC is going from the Input/Output PCB to the variable frequency drive (only when the lights are on). When lights are off, check to e...
  • D
    davisamandaSep 18, 2025
    How to fix water leakage around loading door of Dexter Laundry T-900?
    • J
      Jared WebsterSep 18, 2025
      If there's water leakage around the loading door of your Dexter Laundry Washer, the door may need adjustment due to wear. Check the tightness around the perimeter using a dollar bill. Adjust left-to-right tightness using shims at the door lock or hinge side. Center the gasket to the tub opening before tightening the door to the hinge bolts. Chalk may be used on the tub front to show the point of contact with the tub. If the gasket is deformed, worn, or damaged, replace it.
  • E
    Erica TaylorSep 15, 2025
    What to do if no cold water to tub in wash for Dexter Laundry T-900?
    • J
      James SpencerSep 15, 2025
      If cold water isn't entering the tub during the wash cycle of your Dexter Laundry Washer, check the water valve coil for continuity at its terminals and replace it if there's no continuity. Inspect the water inlet screens for blockages and clean them if necessary. Ensure that the water supply is turned on and operating. Check the black and white wires at the Molex plug on the PCB at the main controller and at the relay PCB. Also, check the pressure switch continuity between terminal contacts; if there's no continuity, inspect the pressure switch hose for obstructions and replace the switch if the hose is clear.
  • S
    Samuel HaleySep 4, 2025
    What to do if my Dexter Laundry Washer does not stop?
    • R
      Rodney MccormickSep 4, 2025
      If your Dexter Laundry Washer does not stop, remember that the main PCB controls the time cycle at the end of the cycle. Also, check the braking resistors for continuity and verify the ohms resistance by Molex.
  • A
    Amy BarnesSep 4, 2025
    Why is there water leakage around loading door of Dexter Laundry T-900?
    • M
      Michael KellerSep 4, 2025
      If water is leaking around the loading door of your Dexter Laundry Washer, the door may need adjustment due to abuse or wear. Check the tightness around the perimeter using a dollar bill. Adjust the left to right tightness by shims at the door lock or hinge side, centering the gasket to the tub opening before tightening the door to hinge bolts. Chalk may be used on the tub front to show the point of contact with the tub. If the gasket is deformed, worn, or damaged, replace it.

Summary

Safety Information

General Safety Warnings and Precautions

Crucial safety information covering personnel, installation, operation, and hazards.

Hazard-Specific Warnings

Details on shock, cut, burn, explosion, fire, and other specific hazards.

Servicing and Troubleshooting Safety

Safety advice for maintenance, repair, and troubleshooting procedures.

Safety Symbol Meaning

Explanation of Safety Symbols

Defines warning, danger, informative, and reminder symbols used in the manual.

Introduction

Product Overview and Definitions

Details model identification, washer characteristics, and technical terms.

Unit Specifications

Washer Technical Specifications

Comprehensive technical data for various washer models.

Instructions

Installation Procedures

Guidance on mounting, anchoring, plumbing, and electrical setup.

Operation and Usage Guidelines

Steps for starting, running, programming, and using the washer.

Maintenance and Troubleshooting

Routine upkeep, fault diagnosis, and repair guidance.

Accessories and Parts Information

Details on installation parts, common service parts, and fuses.

Disposal of Unit

WEEE Symbol and Disposal Guidance

Information on the WEEE symbol and proper product disposal.

Declarations of Conformity

Manufacturer Compliance Statements

Certifications and declarations regarding product standards.

Dexter Laundry T-900 Specifications

General IconGeneral
BrandDexter Laundry
ModelT-900
CategoryWasher
LanguageEnglish

Related product manuals