What to do if my Dexter Laundry Washer does not stop?
If your Dexter Laundry Washer does not stop, remember that the main PCB controls the time cycle at the end of the cycle. Also, check the braking resistors for continuity and verify the ohms resistance by Molex.
Why water does not flush softener compartment in Dexter Laundry Washer?
If water does not flush the softener compartment in your Dexter Laundry Washer, check the water valve coil for continuity at its terminals and replace it if there is no continuity. Also, check the water inlet screens for blockages and clean them if necessary. Ensure that the water supply is turned on and operating.
What to do if Dexter Laundry T-900 Washer does not turn?
If your Dexter Laundry Washer does not turn, check the VFD by removing the inspection panel and record any numbers or letters displayed. If there is no display, turn the power off to the machine at the breaker for 2 minutes and then turn it back on to reset. If there is still no display, replace the VFD.
What to do if Dexter Laundry T-900 Washer starts and does not operate?
If your Dexter Laundry Washer starts but doesn't operate, check the yellow enable wires from relay PCB P13 & motor P14 to VFD advances through cycle are connected. Check the fault code on the VFD before removing power from the drive. Also, check the orange P-15 wire for a signal from the door switches.
Why my Dexter Laundry T-900 Washer does not spin?
If your Dexter Laundry Washer does not spin, check the pressure switch for continuity across terminals #21 & #22, which indicates that the pressure switch has reset to the empty position. If there is no continuity, replace the pressure switch.
How to fix water level too high in Dexter Laundry Washer?
If the water level is too high in your Dexter Laundry Washer, check for blockages in the pressure switch hose. Also, check for the pressure switch opening circuit across the terminals and replace the switch if the contacts do not open.
Why my Dexter Laundry T-900 tumbles in one direction?
If your Dexter Laundry Washer tumbles in only one direction, remove the inspection cover at the rear and record any numbers or letters displayed. Refer to the fault code section for more information. Also, inspect the yellow enable wires from the main relay PCB and at the VFD.
What to do if water comes in but level does not rise in Dexter Laundry T-900 Washer?
If water comes in but the level doesn't rise in your Dexter Laundry Washer, check the drain valve for blockages, and inspect the drain valve motor and gear train. If there is power but the drain valve does not close, replace the valve. Check for power to the drain valve; if there's no power, check the (brn/yel) circuit for power. Also, check the black and white wires at the molex plug on the main PCB controller and at the main relay PCB.
Why water drains slowly from Dexter Laundry Washer?
If water drains slowly from your Dexter Laundry Washer, check the hoses and drain valve for blockages. Clean or increase the size of the drain if necessary. Also, check the building drains for blockages.
Why the door does not lock on my Dexter Laundry T-900?
If your Dexter Laundry Washer door isn't locking, first check the display for a fault code, specifically F1, and follow the tests described in the fault code section if it appears. Then, check that the door locking solenoid is receiving 120VAC from the main relay PCB; replace the solenoid if it is but the door still doesn't lock. Finally, check the door latch switch for continuity when the door is closed; adjust or replace the switch if there is no continuity.
Crucial safety information covering personnel, installation, operation, and hazards.
Details on shock, cut, burn, explosion, fire, and other specific hazards.
Safety advice for maintenance, repair, and troubleshooting procedures.
Defines warning, danger, informative, and reminder symbols used in the manual.
Details model identification, washer characteristics, and technical terms.
Comprehensive technical data for various washer models.
Guidance on mounting, anchoring, plumbing, and electrical setup.
Steps for starting, running, programming, and using the washer.
Routine upkeep, fault diagnosis, and repair guidance.
Details on installation parts, common service parts, and fuses.
Information on the WEEE symbol and proper product disposal.
Certifications and declarations regarding product standards.
General| Brand | Dexter Laundry |
|---|---|
| Model | T-900 |
| Category | Washer |
| Language | English |
To Next Page