What to do if the water level is too high in my Dexter Laundry Washer?
If the water level is too high in your Dexter Laundry Washer, check for blockage in the pressure switch hose. Also, check for the pressure switch opening circuit across terminals. Replace the switch if the contacts do not open.
What does it mean if my Dexter Laundry T-900 Washer machine does not stop?
If your Dexter Laundry Washer machine does not stop, this could be due to the main PCB, which controls the cycle time and end of cycle. Also, check the braking resistors for continuity and verify the ohms resistance at the braking resistors with the wires removed.
What to do if water drains slowly from my Dexter Laundry T-900 Washer?
If water is draining slowly from your Dexter Laundry Washer, check the hoses and drain valve for blockages. Ensure the building drain is of adequate size and inspect building drains for blockages.
What causes my Dexter Laundry T-900 to tumble in one direction?
If your Dexter Laundry Washer tumbles in only one direction, refer to the DISPLAYED WASHER FAULTS section for more information. Also, inspect the yellow enable wires from the main relay PCB and at the VFD.
What to do if water comes in but the level does not rise in my Dexter Laundry Washer?
If water enters your Dexter Laundry Washer but the level doesn't rise, check the drain valve for blockages and inspect the drain valve motor and gear train. If there is power to the valve but the drain valve does not close, replace the drain valve and motor. Check for power to the drain valve; if there's no power, check the (brn/yel) wire at the PCB relay board. If there's no power on the (brn/yel) wire when the washer is in a wash cycle, replace the relay board. Also, check the black and white wire at the Molex plug on the main PCB controller P21 connection and at the PCB relay board P20 connection.
What to do if my Dexter Laundry T-900 door will not open?
If the door of your Dexter Laundry Washer won't open, check to see if the thermoactuator and its mechanism are stuck or binding, preventing the door lock motor from opening. Ensure that the locking thermoactuator isn't receiving 24 VAC (50 Hz) during the last 1 1/2 minutes of the cycle and that the unlocking thermoactuator is receiving 24 VAC (50 Hz) during the last minute of the cycle. If the thermoactuators do not receive voltage at the correct times, change the PCB relay board. If the timing and voltage are correct, replace the thermoactuator.
Why Dexter Laundry T-900 starts then stops?
If your Dexter Laundry Washer starts and then stops, check the following: First, the I/O PCB must have green input lights: DOOR LOCK #3, DOOR CLOSED #4, TUB EMPTY #14, RUN KEY #1. START #1 will be on when pressed. If these lights are not on, check the door switches and wiring to/from the control panel. Also, check if the I/O PCB red output light DOOR SOL. #3 is on and ensure that 120VAC power is at the door locking mechanism. Finally, verify that the linkage rod is adjusted properly.
How to fix water leakage around the loading door of my Dexter Laundry T-900?
If you're experiencing water leakage around the loading door of your Dexter Laundry Washer, the door may need adjustment due to wear. Check the tightness around the door's perimeter using a dollar bill. Adjust the left-to-right tightness using shims at the door lock or hinge side. Ensure the gasket is centered to the tub opening before tightening the door to hinge bolts. Chalk may be used on the tub front to show the point of contact with the tub. If the gasket is deformed, worn, or damaged, replace it.
What to do if my Dexter Laundry T-900 machine starts and does not operate?
If your Dexter Laundry Washer starts but doesn't operate, check the yellow enable wires from the PCB relay board connection P13 & P14 to the VFD. Also, check the connection of the orange wire at P15 from the door switches.
What to do if cold water does not enter the tub in wash cycle of my Dexter Laundry T-900?
If cold water isn't entering the tub during the wash cycle of your Dexter Laundry Washer, start by checking the water valve coil for continuity at the terminals and replace it if there's no continuity. Also, check for 24 VAC (50 Hz) power from the main relay PCB. Inspect the water inlet screens for blockage and clean them if necessary. Ensure that the water supply is turned on and operating correctly. Finally, check the black and white wire at the Molex plug on the main PCB controller P21 connection and at the PCB relay board P20 connection, and examine the pressure switch continuity between terminal contacts. If no continuity, check the pressure switch hose for obstruction. If the hose is okay then change the pressure switch.
Crucial safety information covering personnel, installation, operation, and hazards.
Details on shock, cut, burn, explosion, fire, and other specific hazards.
Safety advice for maintenance, repair, and troubleshooting procedures.
Defines warning, danger, informative, and reminder symbols used in the manual.
Details model identification, washer characteristics, and technical terms.
Comprehensive technical data for various washer models.
Guidance on mounting, anchoring, plumbing, and electrical setup.
Steps for starting, running, programming, and using the washer.
Routine upkeep, fault diagnosis, and repair guidance.
Details on installation parts, common service parts, and fuses.
Information on the WEEE symbol and proper product disposal.
Certifications and declarations regarding product standards.
General| Brand | Dexter Laundry |
|---|---|
| Model | T-900 |
| Category | Washer |
| Language | English |
To Next Page