Why is my Dimplex BF8000ST heating element glowing red?
Small glowing sections on the heating element are normal. However, if larger sections are glowing and causing the heater to trip the thermal cutout, unplug the unit, discontinue use, and replace the heater assembly.
What to do if my Dimplex BF8000ST remote control turns on or off by itself?
If your Dimplex Indoor Fireplace turns on or off by itself, the remote control may have a similar frequency to other remotes nearby, or there could be radio frequency interference. Try replacing the remote control and initializing it to the remote control receiver. If the issue persists, the remote control receiver might be defective and needs replacement, followed by initialization of the remote control.
Why are the lights dimming in the room when my Dimplex BF8000ST Indoor Fireplace is on?
If the lights dim when your Dimplex Indoor Fireplace is on, it might be drawing close to the circuit's current rating. Try moving the unit to another outlet or installing it on a dedicated 15 amp circuit.
What to do if my Dimplex Indoor Fireplace heater is not turning on?
If the heater on your Dimplex Indoor Fireplace isn't turning on, it could be due to loose wiring (trace wiring in unit), a defective thermostat (replace thermostat), a defective heater assembly (replace heater assembly), or a defective remote control receiver (replace remote control receiver).
Why is my Dimplex BF8000ST Indoor Fireplace power cord getting warm?
A slightly warm power cord during heater operation is normal. However, if the power cord gets hot to the touch, it could be defective and should be replaced.
Why is my Dimplex BF8000ST Indoor Fireplace buzzing noise from the control panel?
If there's a buzzing noise from the control panel of your Dimplex Indoor Fireplace, the flame speed controller may be defective and require replacement.
Why is my Dimplex BF8000ST making excessive noise with the heater on?
If your Dimplex Indoor Fireplace is making excessive noise with the heater on, the heater assembly may be dirty. Ensure that exterior intake louvers and the firebox cavity are free of dirt and dust. If the noise persists, the heater assembly may be defective and require replacement.
Why is light leaking around the log set of my Dimplex BF8000ST?
If light is leaking around the log set of your Dimplex Indoor Fireplace, check the log set for proper fit, as it may not be positioned correctly.
Why is my Dimplex Indoor Fireplace flame shuddering?
If the flame in your Dimplex Indoor Fireplace is shuddering, it could be due to a defective flicker motor (replace flicker motor) or a defective flame speed control (replace flame speed control components).
How to fix a flame frozen on Dimplex BF8000ST?
If the flame is frozen on your Dimplex Indoor Fireplace, the flicker motor may be defective (replace flicker motor), the flame speed control may be defective (replace flame speed control components), or the wiring may be loose (check wiring connections).
Instructions for installing the fireplace in a new wall structure.
Guidelines for installing the fireplace into an existing fireplace structure.
Explanation of the manual controls located behind the access panel.
Procedure to reset the heater's safety cutoff switch if it trips due to overheating.
Steps to pair the remote transmitter with the fireplace receiver for the first time.
How to operate the fireplace functions using the remote control transmitter.
Detailed steps for replacing the fireplace's internal light bulbs for flame and log illumination.
Specifications for the three lower bulbs used for flame and ember bed effects.
Specifications for the two upper bulbs that illuminate the log exterior.
Instructions on how to clean the fireplace glass safely without scratching.
Method for cleaning the painted exterior surfaces of the electric fireplace.
Defines the scope of products covered by the limited warranty.
Lists items or conditions not covered by the limited warranty, such as light bulbs.
Outlines the duration and terms of the warranty for different fireplace components.
Details specific exclusions from the warranty, like misuse or unauthorized repairs.
Explains Dimplex's responsibilities for repairing or replacing defective products under warranty.
Clarifies how local laws interact with the terms of the limited warranty.
Technical details including model, volts, watts, BTU, amps, and weight of the fireplace.
Visual representation and measurements of the fireplace unit from different angles.
Basic steps for assembling the fireplace, primarily involving attaching the front glass.
Steps for framing and installing the fireplace into a new wall.
Instructions for integrating the fireplace into an existing fireplace structure.
A list of replaceable parts for the fireplace with corresponding part numbers.
General| Model | BF8000ST |
|---|---|
| Type | Electric Fireplace |
| Fuel Type | Electric |
| Voltage | 120V |
| Power Consumption | 1500W |
| Wattage | 1500W |
| Heating Area (Sq. Ft.) | 400 sq. ft. |
| Flame Effect | Yes |
| Flame Technology | LED |
| Flame Colors | Multi-Color |
| Adjustable Thermostat | Yes |
| Remote Control | Yes |
| Timer | Yes |
| Overheat Protection | Yes |
| Color | Black |
| Material | Metal |
| Control Type | Remote Control |
| BTUs | 5000 BTU |
To Next Page
