Why does my Dimplex BF8000ST circuit breaker trip when turned on?
Your Dimplex Indoor Fireplace may be tripping the circuit breaker due to a short in the unit's wiring, which requires tracing the wiring to resolve. Alternatively, the issue could be due to the circuit's current rating being exceeded by the fireplace and other appliances. To fix this, try plugging the unit into another outlet or installing it on a dedicated 15 amp circuit.
How to fix a flame frozen on Dimplex BF8000ST?
If the flame is frozen on your Dimplex Indoor Fireplace, the flicker motor may be defective (replace flicker motor), the flame speed control may be defective (replace flame speed control components), or the wiring may be loose (check wiring connections).
Why is my Dimplex BF8000ST heater emitting an odor?
It's normal for a new Dimplex Indoor Fireplace heater to emit an odor briefly when first turned on, as it burns off accumulated dust. However, if the odor persists, the heater assembly may be defective and require replacement.
What to do if my Dimplex Indoor Fireplace is not turning on using the remote control?
If your Dimplex Indoor Fireplace isn't turning on with the remote, try initializing the remote control. If that doesn't work, install a new battery in the remote and re-initialize it, along with the receiver, if necessary. In some cases, the remote control or receiver may need to be replaced and initialized.
Why is my Dimplex Indoor Fireplace flame not bright or not visible?
If the flame in your Dimplex Indoor Fireplace is not bright or not visible, the light bulbs may be burnt out (replace light bulbs), the wiring may be loose (check wiring connections), or the light harness may be defective (replace light harness).
Why is my Dimplex Indoor Fireplace heater turning off after a couple of minutes?
If your Dimplex Indoor Fireplace heater turns off after a few minutes, it could be due to a buildup of dirt or dust in the heater assembly. Ensure the exterior intake louvers and firebox cavity are free of dirt and dust. Alternatively, the heater assembly may be defective and require replacement.
Why is my Dimplex BF8000ST Indoor Fireplace power cord getting warm?
A slightly warm power cord during heater operation is normal. However, if the power cord gets hot to the touch, it could be defective and should be replaced.
What to do if my Dimplex Indoor Fireplace heater is not turning on?
If the heater on your Dimplex Indoor Fireplace isn't turning on, it could be due to loose wiring (trace wiring in unit), a defective thermostat (replace thermostat), a defective heater assembly (replace heater assembly), or a defective remote control receiver (replace remote control receiver).
Why are the lights dimming in the room when my Dimplex BF8000ST Indoor Fireplace is on?
If the lights dim when your Dimplex Indoor Fireplace is on, it might be drawing close to the circuit's current rating. Try moving the unit to another outlet or installing it on a dedicated 15 amp circuit.
What to do if my Dimplex BF8000ST remote control turns on or off by itself?
If your Dimplex Indoor Fireplace turns on or off by itself, the remote control may have a similar frequency to other remotes nearby, or there could be radio frequency interference. Try replacing the remote control and initializing it to the remote control receiver. If the issue persists, the remote control receiver might be defective and needs replacement, followed by initialization of the remote control.
Instructions for installing the fireplace in a new wall structure.
Guidelines for installing the fireplace into an existing fireplace structure.
Explanation of the manual controls located behind the access panel.
Procedure to reset the heater's safety cutoff switch if it trips due to overheating.
Steps to pair the remote transmitter with the fireplace receiver for the first time.
How to operate the fireplace functions using the remote control transmitter.
Detailed steps for replacing the fireplace's internal light bulbs for flame and log illumination.
Specifications for the three lower bulbs used for flame and ember bed effects.
Specifications for the two upper bulbs that illuminate the log exterior.
Instructions on how to clean the fireplace glass safely without scratching.
Method for cleaning the painted exterior surfaces of the electric fireplace.
Defines the scope of products covered by the limited warranty.
Lists items or conditions not covered by the limited warranty, such as light bulbs.
Outlines the duration and terms of the warranty for different fireplace components.
Details specific exclusions from the warranty, like misuse or unauthorized repairs.
Explains Dimplex's responsibilities for repairing or replacing defective products under warranty.
Clarifies how local laws interact with the terms of the limited warranty.
Technical details including model, volts, watts, BTU, amps, and weight of the fireplace.
Visual representation and measurements of the fireplace unit from different angles.
Basic steps for assembling the fireplace, primarily involving attaching the front glass.
Steps for framing and installing the fireplace into a new wall.
Instructions for integrating the fireplace into an existing fireplace structure.
A list of replaceable parts for the fireplace with corresponding part numbers.
General| Model | BF8000ST |
|---|---|
| Type | Electric Fireplace |
| Fuel Type | Electric |
| Voltage | 120V |
| Power Consumption | 1500W |
| Wattage | 1500W |
| Heating Area (Sq. Ft.) | 400 sq. ft. |
| Flame Effect | Yes |
| Flame Technology | LED |
| Flame Colors | Multi-Color |
| Adjustable Thermostat | Yes |
| Remote Control | Yes |
| Timer | Yes |
| Overheat Protection | Yes |
| Color | Black |
| Material | Metal |
| Control Type | Remote Control |
| BTUs | 5000 BTU |
To Next Page
