To Next PageTo Next Page
Is it normal for the heating element in my Dimplex Indoor Fireplace to glow red?
Small glowing sections of the heating element in your Dimplex Indoor Fireplace are considered normal. However, if larger glowing sections are causing the heater to trip the thermal cutout, unplug the unit, discontinue use, and replace the heater assembly.
What to do if Dimplex DF3003 Indoor Fireplace does not turn on using the remote control?
If your Dimplex Indoor Fireplace isn't turning on with the remote control, ensure the remote is initialized to the fireplace. If not, initialize the remote control. Also, the remote control might not be working correctly, so install a new battery and reinitialize if needed. If problems persist, consider replacing the Remote Control or Remote Control Receiver and then initialize them.
Why does my Dimplex Indoor Fireplace turn on and off by itself?
If your Dimplex Indoor Fireplace turns on or off by itself, the remote control might have a similar frequency to others nearby. Try changing the frequency of the Remote Control, referring to the Operation Section. Radio frequency disturbance from outside sources could also be the cause, so again, change the remote control frequency. If issues continue, replace the Remote Control and Receiver, and initialize them. A defective Remote Control Receiver could also be the culprit, so replace it and initialize it with the Remote Control.
How to fix Dimplex Indoor Fireplace heater if it's not turning on?
If the heater on your Dimplex Indoor Fireplace isn't turning on, but the flame effect works, first, refer to the Operation Section for proper operation. Second, check for loose wiring in the unit. It could also be a defective Heater On/Off switch, which would need replacement. Lastly, a defective Heater assembly could be the cause, requiring replacement.
Why does my Dimplex DF3003 Indoor Fireplace heater turn off after a few minutes?
If the heater on your Dimplex Indoor Fireplace turns off after a few minutes, it could be due to a buildup of dirt or dust in the heater assembly. Ensure the exterior intake louvers and firebox cavity are free of dirt and dust. Alternatively, the Heater Assembly may be defective and require replacement.
What to do if Dimplex DF3003 Indoor Fireplace does not turn on manually?
If your Dimplex Indoor Fireplace isn't turning on manually, first, refer to the Operation Section for proper operation. Check the Fuse/Breaker Panel to ensure there's incoming power from the electrical wall socket. Also, inspect wiring connections for any looseness. A defective switch (3-Position or On/Off) or a defective Remote Control Receiver could also be the problem, requiring replacement.
How to fix flame shutter on Dimplex DF3003 Indoor Fireplace?
If you have a flame shutter issue with your Dimplex Indoor Fireplace, it could be a defective flicker motor, and you should replace it.
Why is light leaking around the log set of my Dimplex DF3003 Indoor Fireplace?
If light is leaking around the log set of your Dimplex Indoor Fireplace, the log set may not be positioned properly. Check the log set for proper fit.
Is it normal for the Dimplex DF3003 Indoor Fireplace power cord to get warm?
The power cord of your Dimplex Indoor Fireplace may get slightly warm during normal operation when the heater is on. However, if the cord gets hot to the touch, replace the power cord, as it may be defective.
Why is my Dimplex DF3003 making excessive noise when the heater is on?
If your Dimplex Indoor Fireplace makes excessive noise when the heater is on, it could be due to a dirty Heater Assembly. Ensure the exterior intake louvers and firebox cavity are free of dirt and dust. Alternatively, the Heater Assembly may be defective and require replacement.
General| Model | DF3003 |
|---|---|
| Type | Electric Fireplace |
| Fuel Type | Electric |
| Voltage | 120 V |
| Power Consumption | 1500 W |
| Heating Area | 400 sq. ft. |
| Adjustable Thermostat | Yes |
| Remote Control | Yes |
Step-by-step instructions for installing the fireplace into an existing fireplace structure.
Guidance on preparing a new wall opening and framing for fireplace installation.
Instructions for installing the fireplace with a mantel surround kit or custom-built surround.
Explanation of the manual controls on the fireplace unit, including ON/OFF, dimmer, and action controls.
Procedure for replacing the internal light bulbs that create the flame and ember effects.
Specifies the Dimplex fireplace models and trims covered by the limited warranty.
Lists items and conditions not covered by the manufacturer's limited warranty.
Details the duration and scope of coverage for parts and labor under the warranty.
