Directed VOXX DEI DS3+ - User Manual

37 pages

Save Page as PDF

To Next Page

Functions compatible with the 2022 Honda HR-V (Smart Key)

*Telematics features: The telematics features listed below (with an asterisk) ONLY apply when using SmartStart Pro.

* Odometer

3x LOCK START (Start control using OEM Remote)

3x LOCK STOP (Stop control using OEM Remote)

Accessory Activation

Arm Factory Security

Brake Status (foot brake)

Control of aftermarket alarm with OEM remote

Disarm Factory Security

Door Lock Control

Door Locks Status

Door Unlock

Driver Priority Unlock

E-Brake Status

Entry Monitoring ALL Door Pins

Entry Monitoring Hood Pin

Entry Monitoring Trunk/Hatch Pin

Factory Alarm Trigger Monitoring

Fuel level/EV battery level

Ignition Activation

Ignition Status

Immobilizer Bypass-Data No Key Req'd

Key2GO

RAP Shut Down (Retained ACC Power)

Remote Start Takeover

SmartStart

Start (Crank) Activation

Tach / RPM Output

Trunk / Hatch Release

933.HONDA9

v2.10.198.12

2022 Honda HR-V (Smart Key)

THHON11, THHON1-NO-TAKEOVER, THHON9-

TAKEOVER Compatible

(Sold Separately)

Main Page

Questions and Answers

S
Sherry StephensonSep 15, 2025
Why Directed VOXX DEI DS3+ OBDII feature is not supported?
- A
  Aaron HarrisSep 15, 2025
  The diagnostic data bus was not detected, therefore the SmartStart features will be limited in your Directed Automobile Accessories.
A
Allison BakerSep 15, 2025
Why Directed VOXX DEI DS3+ PTS shutdown error?
- G
  Gregory HicksSep 15, 2025
  The PTS output from the Directed Automobile Accessories module was not activated due to safety protection.
W
william62Sep 15, 2025
What to do if Directed VOXX DEI DS3+ Automobile Accessories CAN1 not detected?
- Q
  qshawSep 15, 2025
  Check the CAN1 Tan and Tan/Black wire connections. Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times.
F
frankdanielsSep 15, 2025
What to do if Directed VOXX DEI DS3+ Automobile Accessories CAN2 not detected?
- T
  Todd WilliamsonSep 15, 2025
  Check the CAN2 Orange/Green and Orange/Brown wire connections. Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times.
W
William TaylorSep 15, 2025
What to do if Directed VOXX DEI DS3+ Automobile Accessories J1850 not detected?
- S
  sabrina68Sep 16, 2025
  Check the J1850 wire connection. Wake up the data bus by turning the ignition on and try again.
R
Robert ClaytonSep 16, 2025
What does 'Waiting to begin the programming sequence' mean for Directed Automobile Accessories, and how to solve it?
- J
  joanna10Sep 16, 2025
  This indicates that the programming sequence is not starting. To resolve this, ensure you are following the correct programming procedure.
M
Mark MosesSep 16, 2025
What does it mean 'Initialization failed' for Directed VOXX DEI DS3+ Automobile Accessories?
- J
  Jennifer HallSep 16, 2025
  Reset the module and complete the programming again. If the issue persists, please contact Technical Support.
C
Caitlin UnderwoodSep 16, 2025
What does 'Bypass processing error' mean for Directed Automobile Accessories?
- J
  Jeffrey BushSep 16, 2025
  The bypass calculation failed. Reset the module and try again. If the condition persists, please contact Technical Support.
Z
znicholsSep 16, 2025
Why Directed VOXX DEI DS3+ transponder functions were skipped?
- K
  Kimberly FuentesSep 16, 2025
  If compatible, when the RXT mode is not desired or convenience features are needed, please reset and reprogram the module.
J
Julia SimpsonSep 16, 2025
What does it mean 'Bypass and CAN were skipped' in Directed VOXX DEI DS3+ Automobile Accessories?
- D
  Dillon ArmstrongSep 16, 2025
  This means that the programming button was pressed 5 times to skip bypass and 5 times to skip the CAN.