Directed DBALL - User Manual

Questions and Answers

S
Steven HoffmanAug 18, 2025
How to troubleshoot Directed Automobile Accessories module with no power?
- R
  Ryan WeissAug 18, 2025
  If your Directed Automobile Accessories module isn't getting power, ensure the D2D harness is securely connected and that 12 volts are present between the red and black wires. If the voltage is correct, the module itself may be defective.
B
Brian CastroAug 20, 2025
What to do if Directed DBALL Automobile Accessories bypass data is not detected?
- B
  Brooke YoungAug 20, 2025
  If your Directed Automobile Accessories system indicates that bypass data is not being detected, check the bypass line connection. If multiple wires are involved, verify they are not inverted. Also, start the vehicle with the key to ensure the original equipment is still functioning correctly.
K
Kelly PetersonAug 23, 2025
Why is my Directed DBALL waiting to begin the programming sequence?
- V
  victor99Aug 23, 2025
  If your Directed Automobile Accessories module is stuck waiting to begin the programming sequence, double-check that the ignition input is correctly connected.
J
Jasmine TurnerAug 26, 2025
What to check if Directed DBALL Automobile Accessories start command is received but not working?
- S
  Samantha RussellAug 26, 2025
  If the Directed Automobile Accessories module fails to flash after receiving the start command, it indicates the module didn't receive the signal. When using XL202, check the cable connection. For SmartStart, confirm SmartStart is configured in D2D.
R
rwalkerAug 27, 2025
How to fix Directed Automobile Accessories when CAN C not detected?
- B
  bishopjamesAug 28, 2025
  If your Directed Automobile Accessories system reports that CAN C is not detected, the first step is to check the CAN connections to ensure they are properly made.
W
Wendy PearsonAug 30, 2025
Why Directed DBALL says OBDII feature not supported?
- K
  kathryn73Aug 30, 2025
  The 'OBDII feature not supported' message on your Directed Automobile Accessories could be due to missing wire connections or limitations of the module's hardware. Refer to the wiring installation section to verify all connections.
C
Chelsea NguyenSep 2, 2025
What to do if Directed Automobile Accessories initialization failed?
- L
  Lauren McleanSep 2, 2025
  If your Directed Automobile Accessories module fails to initialize, attempt a complete Hard Reset. If a second attempt fails, connect the module to Directechs.com and contact Tech Support, having the module ID ready.
K
Karen ClarkSep 4, 2025
What does 'GROUND OUT ON (GWR) command received' mean for Directed Automobile Accessories?
- F
  ferrellbrittneySep 4, 2025
  If your Directed Automobile Accessories receives a 'GROUND OUT ON (GWR)' command, it means the Ground While Running (status) signal was either lost or never received by the module. Commands can originate from RF, D2D, or W2W.
V
Veronica LopezSep 7, 2025
What does 'IGNITION ON command received' mean on Directed DBALL Automobile Accessories?
- M
  Mr. Justin Richmond MDSep 7, 2025
  If your Directed Automobile Accessories system indicates 'IGNITION ON command received,' it suggests the module isn't receiving the ignition signal. In a W2W installation, this will only appear if the ignition input wire is in use.
D
David HernandezSep 9, 2025
Why Directed Automobile Accessories lock command is not working?
- P
  pamelagarciaSep 9, 2025
  If the bypass module fails to flash after a LOCK command is received by your Directed Automobile Accessories, it indicates that the module did not receive the signal.