Directed VOXX DEI DS3+ - User Manual

37 pages

Save Page as PDF

To Next Page

Functions compatible with the 2022 Honda HR-V (Smart Key)

*Telematics features: The telematics features listed below (with an asterisk) ONLY apply when using SmartStart Pro.

* Odometer

3x LOCK START (Start control using OEM Remote)

3x LOCK STOP (Stop control using OEM Remote)

Accessory Activation

Arm Factory Security

Brake Status (foot brake)

Control of aftermarket alarm with OEM remote

Disarm Factory Security

Door Lock Control

Door Locks Status

Door Unlock

Driver Priority Unlock

E-Brake Status

Entry Monitoring ALL Door Pins

Entry Monitoring Hood Pin

Entry Monitoring Trunk/Hatch Pin

Factory Alarm Trigger Monitoring

Fuel level/EV battery level

Ignition Activation

Ignition Status

Immobilizer Bypass-Data No Key Req'd

Key2GO

RAP Shut Down (Retained ACC Power)

Remote Start Takeover

SmartStart

Start (Crank) Activation

Tach / RPM Output

Trunk / Hatch Release

933.HONDA9

v2.10.198.12

2022 Honda HR-V (Smart Key)

THHON11, THHON1-NO-TAKEOVER, THHON9-

TAKEOVER Compatible

(Sold Separately)

Main Page

Questions and Answers

K
kristenpowellSep 18, 2025
What to do if CAN1 is not detected in Directed Remote Starter?
- J
  Joy TurnerSep 18, 2025
  Verify the connections of the CAN1 Tan and Tan/Black wires. Then, wake up the data bus by turning the ignition on and try again. If your installation doesn't need this connection, skip this step by pressing the programming button 5 times.
B
Beverly WagnerSep 18, 2025
What to do if J1850 is not detected on Directed Remote Starter?
- B
  Bryan HamiltonSep 18, 2025
  Check the J1850 wire connection. Then, wake up the data bus by turning the ignition on and try again.
K
Kenneth WalkerSep 18, 2025
What to do if Directed Remote Starter shows a bypass processing error?
- E
  Elizabeth RichardsonSep 22, 2025
  The bypass calculation has failed. Reset the module and try again.
J
Jessica PenningtonSep 22, 2025
What to do if Directed Remote Starter is waiting to begin the programming sequence?
- L
  luis44Sep 22, 2025
  Make sure that you are following the correct programming procedure.
S
Stephanie StevensSep 22, 2025
Why is the CAN bus incorrectly detected in my Directed Remote Starter?
- P
  Patricia GarrettSep 22, 2025
  Verify the CAN1 and CAN2 connections.
S
Sara HallSep 22, 2025
How to fix Directed Remote Starter initialization failed?
- V
  Veronica BriggsSep 22, 2025
  Reset the module and complete the programming again.
P
Peter WoodsSep 22, 2025
Why Directed Automobile Accessories says 'Runsafe was not disabled'?
- M
  Mrs. Katherine MoralesSep 22, 2025
  No UNLOCK command was received prior to opening the door, or the 45 second timer expired in takeover mode.
A
antonio65Sep 22, 2025
What does 'PTS shutdown error' mean on my Directed VOXX DEI DS3+ Automobile Accessories?
- E
  Eric EllisonSep 22, 2025
  The PTS output from the module was not activated due to safety protection.
T
Tonya NguyenSep 22, 2025
Why Directed Automobile Accessories says 'Brake was not detected'?
- D
  Diamond WeberSep 23, 2025
  The brakes were not detected, which prevents the system from shutting down the vehicle.
J
Joseph WilliamsSep 23, 2025
Why Directed VOXX DEI DS3+ says 'Smart key was not detected'?
- M
  Michael PriceSep 23, 2025
  The smart key was not detected, which prevents the system from shutting down the vehicle.