dixell XC660D User Manual

1592001850 XC660D GB r3.4 04.09.2017.docx XC660D 26/55
LP2 = Low pressure switch for circuit 2,
ES = Energy saving;
oFF = instrument shut down;
LL = liquid level alarm
SIL = to enable the silence function
EAL = generic external alarm, it doesn’t affect the regulation
Co1 = running proof function for load 1, term. 1-2
Co2 = running proof function for load 2, term. 3-4
Co3 = running proof function for load 3, term. 5-6
Co4 = running proof function for load 4, term. 7-8
Co5 = running proof function for load 5, term. 9-10
Co6 = running proof function for load 6, term. 11-12
NOTE: also the following values LP1, HP are present. These values must not be used
iF02 Digital input 2 configuration (13-15) – For the values see iF01; Factory setting oA2.
iF03 Digital input 3 configuration (16-17) – For the value see iF01; Factory setting oA3
iF04 Digital input 4 configuration (16-18) – For the value see iF01; Factory setting oA4
iF05 Digital input 5 configuration (19-20) – For the value see iF01; Factory setting oA5
iF06 Digital input 6 configuration (19-21) – For the value see iF01; Factory setting oA6
iF07 Digital input 2 configuration (22-23) - For the values see iF01; Factory setting ES.
NB: THE ABOVE FUNCTIONALITIES ARE ENABLED ONLY WHEN P4C=NP. With
P4C = nt10 or nt86 this input is operating as a NTC 10K temperature sensor or NTC
86K temperature sensor
iF08 Digital input 8 configuration (22-24): For the values see iF01; Factory setting LL
iP01 Digital input 1 polarity (13-14):
oP: the digital input is activated by opening the contact;
CL: the digital input is activated by closing the contact.
iP02 Digital input 2 polarity (13-15):
oP: the digital input is activated by opening the contact;
CL: the digital input is activated by closing the contact.
iP03 Digital input 3 polarity (16-17):
oP: the digital input is activated by opening the contact;
CL: the digital input is activated by closing the contact.
iP04 Digital input 4 polarity (16-18):
oP: the digital input is activated by opening the contact;
CL: the digital input is activated by closing the contact.
iP05 Digital input 5 polarity (19-20):
oP: the digital input is activated by opening the contact;
CL: the digital input is activated by closing the contact.
iP06 Digital input 6 polarity (19-21):
oP: the digital input is activated by opening the contact;
CL: the digital input is activated by closing the contact.
iP07 Digital input 7 polarity (22-23):
oP: the digital input is activated by opening the contact;
CL: the digital input is activated by closing the contact.
iP08 Digital input 8 polarity (22-24)
oP: the digital input is activated by opening the contact;
CL: the digital input is activated by closing the contact.
iP09: Polarity of High pressure-switch alarm (terminals 45-46)
oP =HP alarm is signaled without voltage presence
cL= HP alarm is signaled with voltage presence
iP10: Polarity of Low pressure-switch alarm (terminals 44-45)
oP =LP alarm is signaled without voltage presence
cL= LP alarm is signaled with voltage presence
d1d Digital input set as oA1 or Co1 activation delay (0÷255s), This delay it is considered
when i1F or i2F or i3F or i4F or i5F or i6F or i7F or i8F is set as oA1 or Co1

dixell XC660D Specifications

General

Brand	dixell
Model	XC660D
Category	Controller
Language	English