EasyManua.ls Logo

Dorma CS 80 MAGNEO User Manual

Dorma CS 80 MAGNEO
10 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
Auf-Wand Montage On-wall mounting
CS 80 MAGNEO
WN 058347 45532, 11/12
Türenkit Glasklemmschiene / Door kit glass clamping rail
Für eine vollständige Türinstallation benötigen Sie:
Verkleidungs-/ Befestigungskit für Glasklemmschiene
Türenkit Glasklemmschiene
Glastürflügel
CS 80 MAGNEO Antrieb
Montagewinkel
mounting bracket
Ausgleichsbleche
shim plates
Befestigungswinkel In-Wand Montage
Bracket for in-wall mounting
Futterplatte (Zubehör)
shim plate (option)
Bodenführung In-Wand Montage
Floor guide rail for in-wall mounting
Glasklemmschiene
glass clamping rail
Antrieb nicht im Lieferumfang enthalten.
operator not part of the scope of delivery
Verkleidung
cover
Türflügel nicht im Lieferumfang enthalten
Door panel not part of the scope of
delivery.
floor guide
Bodenführung
Inhaltsverzeichnis contents
D Arbeitsvorbereitung und Hinweise 2 - 5
Montage 6 - 10
GB Required preparation and instructions 2 - 5
Mounting 6 - 10
To build a complete door system you need:
operator
Cover kit/fixing kit for glass clamping rail
Door kit glass clamping rail
Glas door panel
CS 80 MAGNEO
Die DORMA MAGNEO Schiebetürautomatik ist ein
Baukastensystem.
Das vorliegende ist eine Komponente des
Baukastensystems DORMA MAGNEO
Schiebetürautomatic.
Für eine vollständige Türinstallation benötigen Sie
zusätzlich zu diesem noch folgende
Kompontenen: Türflügel (Extern), das Verkleidungs- und
Befestigungskit, den Antrieb und soweit gewünscht das
zusätzliche Zubehör.
CS 80
Türenkit
CS 80
Türenkit
The sliding door is a modular
system.
The present door kit is one component of the modular
system s .
DORMA MAGNEO
DORMA MAGNEO
CS 80
CS 80 liding door
or a complete door installation you will need the following
components in addition to this kit:door leaf (external),
cover- and fixing kit, the drive unit and as far as desired
additional accessories.
F

Other manuals for Dorma CS 80 MAGNEO

Questions and Answers:

Dorma CS 80 MAGNEO Specifications

General IconGeneral
BrandDorma
ModelCS 80 MAGNEO
CategoryDoor Opening System
LanguageEnglish

Summary

Before You Start

Opening Direction

Safety Instructions

Specified Standard Operation

CS 80 MAGNEO is designed for opening/closing interior doors up to 80kg.

Product-Specific Characteristics

CS 80 MAGNEO is designed for single-panel interior doors.

Standards, Laws, Codes and Regulations

Automatic doors can cause hazards; residual risks cannot be excluded.

Low-Energy Product Compliance

Closing Edge Hazards

Protection Requirements

Optional Safety Sensors

Safety sensors are optional for closing edges based on risk assessment.

Full Energy Mode Safety

Higher forces in Full Energy mode require safety kit installed by specialist.

Installer Risk Assessment

Assess need for safety sensors based on site conditions and user groups.

Protection for Vulnerable Users

Liability and Documentation Notes

General Installation and Maintenance

Power Disconnection

Disconnect power before mounting, maintenance, or cleaning.

Workplace Safety

Secure work area, use appropriate mounting hardware.

Electrical Safety

Qualified Personnel Requirement

Only qualified professionals may open the power connection housing.

Power Cable Precautions

Ensure cables are not tripping hazards and are handled by the plug.

Awarded Safety Standards

CS 80 MAGNEO meets low-energy, tested safety, and CE standards.

Mounting Bracket Installation

Door Panel Connection Preparation

Operator Mounting to Bracket

Permanent Power Supply Connection

Component Measurement and Cutting

Glass Clamping Rail Installation

Cleaning for Clamping

Ensure glass pane and clamping rail are clean and grease-free in the clamping area.

Noise Reduction and Finishing

Apply foam rubber for noise, slide on cover, and press on end caps.

Door Panel Hanging and Alignment

Floor Guide Rail Installation

End Stop Adjustment

Cover Preparation and Mounting

Commissioning the System

Initial System Check

Verify the door moves smoothly over its complete path.

Power Connection and Activation

Connect power and switch on the operator; perform learning cycle if needed.

Related product manuals