Dormakaba ES 400 PRO - Disassembly, Recycling and Disposal; EC Declaration of Conformity; EC Declaration of Incorporation

18
WN 059666 45532 - 07/2023
ES 250 PRO/ES 250 PRO FST
ES 400 PRO/ES 400 PRO FST
Operating instructions
7 Disassembly, recycling and disposal
Disassembly is carried out in the reverse order of mounting and must be carried
out by qualified personnel.
WARNING
Danger to life through electric current
Work on electrical units must only be carried out by qualified electricians.
• Before starting work on electrical units and equipment, establish a
voltage-free state and maintain this state for the entire duration of
the work.
The product must be disposed of in an environmentally friendly manner.
Electrotechnical parts and batteries must not be disposed of as domestic
waste. Dispose of electrotechnical parts and batteries in the designated
acceptance and collection points. Refer to the statutory regulations for
your country.
8 EC declaration of conformity
dormakaba Deutschland GmbH, DORMA Platz 1, 58256 Ennepetal
hereby declares that the products
ES 250 PRO, ES 250 PRO FST, ES 250 PRO T, ES 250 PRO T FST, ES 400 PRO, ES 400 PRO FST,
ES 400 PRO T, ES 400 PRO T FST, ES 500 PRO, ES 250 PRO EASY, ES 250 PRO EASY T
are in conformity with the provisions of the following EC Directives and that the following standards
have been applied.
EC Directives:
2014/30/EU Electromagnetic Compatibility
2011/65/EU RoHS
Harmonized European standard, national rules:
EN13849-1 ENISO12100 EN16005 EN60335-2-103
EN 61000 - 6 - 2 EN 61000 - 6 - 3 EN 61000 - 3 - 2 EN 61000 - 3 – 3
ENIEC63000
System components:
Expansion modules:
Operating mode switch (BAS), safety and activation (SIAK), inputs and outputs (I/O)
9 EC declaration of incorporation
dormakaba Deutschland GmbH, DORMA Platz 1, 58256 Ennepetal
hereby declares that the partly completed machinery
ES 250 PRO, ES 250 PRO FST, ES 250 PRO T, ES 250 PRO T FST, ES 400 PRO, ES 400 PRO FST,
ES 400 PRO T, ES 400 PRO T FST, ES 500 PRO, ES 250 PRO EASY, ES 250 PRO EASY T
conforms to the following essential requirements of the Machinery Directive
(2006/42/EC) - Annex I, Article:
1.1.3, 1.1.5, 1.2.1, 1.2.3, 1.2.5, 1.2.6, 1.3.2, 1.3.3, 1.3.4, 1.3.8.1, 1.3.9, 1.5.1, 1.5.2, 1.5.4- 1.5.10, 1.5.16, 1.6.1, 1.6.2, 1.6.3,
1.6.4, 1.7.1.1, 1.7.3, 1.7.4
The partly completed machinery continues to comply with all relevant provisions of Directives 2014/35/
EU and 2014/30/EC.
It may be installed and operated in automatic door units according to the Machinery Directive if the
unit manufacturer ensures that all requirements resulting from the Machinery Directive are complied
with and issues an EC declaration of conformity.
The specialist technical documents have been created and are available from the Product Compliance
Manager at: product-compliance.germany@dormakaba.com.
They will be transmitted electronically to national authorities upon reasoned request.