What does Yellow LED – 8 Flashes mean on DSC Cell Phone?
If the DSC Cell Phone shows a Yellow LED flashing 8 times, it indicates a receiver supervision trouble. This trouble appears when supervision is enabled, but the unit cannot successfully communicate with the receiver. If this issue continues, contact the central station.
What to do if BootLoader Failed on DSC Cell Phone?
If the DSC Cell Phone's initialization sequence is taking more than several minutes, the boot loader might have failed. To confirm, enter communicator programming [*][8][installer code][851]. If access is granted, continue waiting for the initialization sequence to complete. If access is denied (long error tone), disconnect and reconnect power to the communicator module.
How to solve Yellow LED – 2 Flashes on DSC TL280 Cell Phone?
If your DSC Cell Phone shows a Yellow LED flashing two times, it indicates a panel supervision trouble. Check that section [382] toggle option [5] is ON (Alternate Communicator Enabled). Also, make sure the PC-LINK cable between the panel and communicator is connected properly (not reversed) and is securely in place.
What does it mean when my DSC TL280 shows a Yellow LED flashing 12 times?
If your DSC Cell Phone displays a Yellow LED flashing 12 times, it indicates a module configuration trouble. This usually means that the system account code in section [021] or the receiver account code in sections [101] or [111] has not been programmed. Make sure a valid account code has been entered in these sections.
Why are the Red and Yellow LEDs flashing together on my DSC Cell Phone?
If the DSC Cell Phone displays both Red and Yellow LEDs flashing together, it means the unit is in the initialization sequence. Wait while the unit gets its programming and establishes a connection to all programmed receivers. Note that this process may take several minutes.
What to do if DSC Cell Phone shows Yellow LED flashing 7 times?
If the DSC Cell Phone has a Yellow LED flashing 7 times, it means the receiver is not available. Ensure that the Ethernet path has Internet connectivity. If you are using a static IP address, verify that the gateway and subnet mask are entered correctly. If your network uses a firewall, ensure that the programmed outgoing ports are open (default UDP port 3060 and port 3065). Also, ensure that all receivers are programmed for DHCP or have the correct IP address and port number.
How to fix DSC TL280 Cell Phone with no indication?
If your DSC Cell Phone shows no indication, the cause might be no power. Check the power connections between the panel and the communicator and confirm that the PC-LINK cable is properly installed between the communicator and the panel.
Covers various risks including system failures, component issues, environmental impacts, and device limitations.
Covers essential installation practices and critical warnings like lightning protection.
Instructions for installers to convey safety and service information to end-users.
Provides specifications for power, environment, mechanicals, and lists compatible receivers/panels.
Details mounting the communicator into compatible panels like HS2016/2032/2064/2128.
Provides wiring diagram and steps for electrical connection, including power and RS-232.
Highlights critical warnings about power limitation and wiring separation.
Specific programming steps for HS2016/2032/2064/2128 panels to ensure communicator function.
Details communicator troubles, status LEDs, and specific indications like Panel Supervision Trouble.
Details specific troubles indicated by yellow LED flashes (Ethernet, Receiver, FTC, Module).
Configures IP addresses, subnet mask, gateway, DNS servers, and receiver supervision.
Provides options to reset the module to factory defaults or perform a soft reset.
General| Product type | Ethernet alarm communicator |
|---|---|
| Compatible products | HS2016/ HS2032/ HS2064/ HS2128 Sur-Gard System I-IP/II/III/IV/5 PC5003C, PC4050C and PC405CAR |
| Security algorithms | 128-bit AES |
| Serial ports quantity | 1 |
| Ethernet LAN data rates | 10, 100 Mbit/s |
| Ethernet interface type | Fast Ethernet |
| Input current | 0.1 A |
| Input voltage | 10.8 - 12.5 V |
| Operating temperature (T-T) | 5 - 40 °C |
Weight and Dimensions| Depth | 115 mm |
|---|---|
| Width | 150 mm |
| Package weight | 310 g |
To Next Page
