Why is my DURAVIT Plumbing Product not flushing the ceramic well enough?
If the ceramic on your DURAVIT Plumbing Product isn't flushing adequately, the flush volumes may be set incorrectly. Try increasing the flush volume.
How to fix DURAVIT DuraSystem A2 actuator plate when it does not work?
If the actuator plate on your DURAVIT Plumbing Product isn't working, it might be due to an interruption in the power supply. Restore the power supply to resolve this.
What to do if water runs continuously into the ceramic of DURAVIT Plumbing Product?
If water is continuously running into the ceramic of your DURAVIT Plumbing Product, it could be due to a software malfunction. Try disconnecting the power supply for 10 seconds and then restoring it.
Why does button lighting light up continuously on DURAVIT Plumbing Product?
If the button lighting on your DURAVIT Plumbing Product is continuously lit, there might be an obstacle within the detection range, like furniture. Try removing any obstacles. Alternatively, the presence detection might be incorrectly set; switch to presence detection in special mode, especially if you have a small room.
Why does DURAVIT DuraSystem A2 odour extraction stop right after leaving the toilet?
If the odour extraction on your DURAVIT Plumbing Product stops immediately after you leave the toilet, the run-on time might be set to 0 minutes. Activate or extend the run-on time.
How to stop DURAVIT Plumbing Product odour extraction immediately after leaving the toilet?
If the odour extraction on your DURAVIT Plumbing Product doesn't stop immediately after you leave the toilet, the run-on time is likely set to a value greater than 0 minutes. Deactivate or reduce the run-on time.
What to do if hygiene flush does not work on DURAVIT Plumbing Product?
If the hygiene flush isn't working on your DURAVIT Plumbing Product, it could be because the actuator plate has been used since the last hygiene flush. In this case, the hygiene flush will occur at the end of the next interval. It's also possible that the hygiene flush is deactivated; if so, activate it.
Why does DURAVIT DuraSystem A2 Plumbing Product button lighting not work?
If the button lighting on your DURAVIT Plumbing Product isn't working, it could be because the cleaning function or child safety lock is activated. The buttons will reappear automatically after 2 minutes.
Why does the night light stay on continuously on my DURAVIT Plumbing Product?
If the night light on your DURAVIT Plumbing Product lights up continuously, it may be because the ambient light is too low. Try deactivating the night light. Alternatively, the actuator plate could be dirty or wet; clean or dry it.
Why does DURAVIT DuraSystem A2 odour extraction start automatically?
If the odour extraction on your DURAVIT Plumbing Product starts automatically, the automatic mode is likely activated. This is the factory setting. Adjust the mode if necessary.
Visual guide to the actuator plate components and layout.
Explains the meaning of different LED colors on the actuator plate.
Explains LED behavior related to presence detection modes.
Defines important terms and symbols used in the manual.
Introduces general safety guidelines and the product's intended purpose.
Highlights dangers of electric shock and risks from improper product handling.
Provides crucial safety instructions for battery use and storage.
Step-by-step guide for the initial setup of the actuator plate.
Explains the fundamental principles of touch-free activation.
Instructions for performing long and short flushes.
Guide on how to modify flush water volume using the remote.
How to activate or deactivate the automatic flushing feature.
Procedure to manually drain the cistern if needed.
Activating, deactivating, and setting the hygiene flush function.
How to manually trigger a flush in emergency situations.
How to manually start or stop the odour extraction.
Activating and deactivating the automatic odour extraction feature.
Adjusting the duration the fan runs after flushing.
Adjusting the intensity of the odour extraction fan.
Temporarily locking buttons for cleaning purposes.
Managing the automatic night light feature.
Enabling and disabling the child safety lock mechanism.
Procedure to restore all settings to default.
Customizing presence detection ranges in normal mode.
Configuring presence detection specifically for small room environments.
How the unit operates during power outages.
Step-by-step instructions for replacing the battery.
Steps to detach the actuator plate for maintenance.
Procedures for disconnecting cables and removing the mounting frame.
Detailed steps for releasing the battery compartment and swapping batteries.
Reconnecting the battery compartment and managing cables.
Installing the threaded rod for manual flush mechanism.
Steps for putting back the protective plates and mounting frame.
Reconnecting the electrical wiring to the actuator plate.
Final step of attaching the actuator plate to the frame.
How to properly clean the actuator plate surface.
Instructions for disposing of electronic equipment, batteries, and packaging.
Diagnosing issues based on actuator plate LED indicator behavior.
Resolving common problems related to the actuator plate's general operation.
Solutions for issues with the flushing mechanism.
Addressing problems with the hygiene flush feature.
Diagnosing and fixing issues with the odour extraction system.
Resolving problems related to the night light feature.
Information found on the product's identification label.
Electrical, operating temperature, and protection ratings.
Information on the types of batteries used.
General| Product Type | Concealed Cistern |
|---|---|
| Height | 1120 mm |
| Installation Type | Wall-Mounted |
| Flush Type | Dual Flush |
| Flush Volume | 3/6 liters |
| Rim Type | Rimless |
| Water Connection | 1/2 inch |
| Application | WC |
To Next Page