Elentek SMART PRO - User Manual

SMART PRO - User Manual
ELECTRICAL PANEL FOR 1 OR 2 MOTORS

Summary

Introduction to the User Manual

Safety Warnings and Precautions

Product Overview and Specifications

Installation Guidelines and Procedures

Control Panel Indicators and Keys

Main Board Inputs and Outputs Description

Expansion Input Modules

7.1 RS485 Expansion

Module for RS485 communication standard with MODBUS protocol.

7.2 Voltage-Free Contact Output Expansion

Module for 6 digital outputs for signalling.

7.3 Probe Input Expansion for Motor Start

PRO-SL input module for motor start and level signalling.

7.4 Probe Input Expansion for Water Seepage

RL-H2O input module for motor control.

7.5 Buffer Battery Device Expansion

PRODBT module for buffer battery connection.

7.6 Bluetooth-WIFI Expansion

Allows panel connection via Wi-Fi or Bluetooth for Elentek APP.

Motherboard DIP-Switch Settings

8.1 DIP-SWITCH 1: Level Alarm Signalling

Configures level alarm signalling from probe input.

8.2 DIP-SWITCH 2: Ammeter Trip Delay

Selects thermal switch activation delay time (5 or 10 seconds).

8.3 DIP-SWITCH 3: Klixon Input Deactivation

Enables or disables Klixon input for overtemperature control.

8.4 DIP-SWITCH 4: Alarm Reset from Klixon

Selects manual or automatic reset for overtemperature alarm.

8.5 DIP-SWITCH 5: Filling;Emptying Mode

Selects probe input use for filling or emptying mode.

8.6 DIP-SWITCH 6: Self-Holding Enable

Activates self-holding for start/stop floats.

8.7 DIP-SWITCH 7: Delayed Board Activation

Enables delayed board activation on power return.

8.8 DIP-SWITCH 8: Motor Switching Module

Enables automatic switching of motors.

DIP-Switch Settings Display

9.1 DIP-SWITCH 1: Input Reversal

Inverts enabling of digital inputs G/P1, G/P2, G.A.

9.2 DIP-SWITCH 2: Phase Sequence Control

Disables missing or incorrect phase sequence check.

9.3 DIP-SWITCH 3: Self-Test Enable

Enables motor self-test functionality.

9.4 DIP-SWITCH 4: Manual Push or Impulse Key

Sets operation of the manual key (push or impulse).

Trimmer Settings and Calibration

10.1 TRIMMER SENS. PROBE: Probe Sensitivity

Adjusts sensor sensitivity for liquid conductivity.

10.2 TRIMMER MIN: Minimum Current Activation

Adjusts minimum motor current for dry run protection.

10.3 MAX TRIMMER: Current Overload Activation

Adjusts maximum motor current for overload protection.

Board Component Layout and Specifications

Standard Wiring Diagrams

12.1 SMART PRO Single Phase (230 V) Wiring Diagram

Wiring diagram for single-phase 230V SMART PRO model.

12.2 SMART PRO Three Phase (400 V) Wiring Diagram

Wiring diagram for three-phase 400V SMART PRO model.

Expansion Module Wiring Diagrams

13.1 PRO-RS485 Expansion Wiring

Wiring diagram for RS485 expansion module.

13.2 Voltage-Free Contact Expansion Wiring

Wiring diagram for voltage-free contact output expansion.

13.3 PRO-SL Probe Input Wiring

Wiring diagram for PRO-SL probe input module.

13.4 PRO-SL H20 Probe Input Wiring

Wiring diagram for PRO-SL H20 probe input module.

Specific Model Wiring Diagrams

14.1 SMART PRO LED 1 MONO Wiring

Wiring diagram for SMART PRO LED 1 MONO.

14.2 SMART PRO LED 2 MONO Wiring

Wiring diagram for SMART PRO LED 2 MONO.

14.3 SMART PRO LED 1 TRI Wiring

Wiring diagram for SMART PRO LED 1 TRI.

14.4 SMART PRO LED 2 TRI Wiring

Wiring diagram for SMART PRO LED 2 TRI.

RS485 Modbus Communication Addresses

Product Size Table

Troubleshooting Common Problems

Elentek SMART PRO Specifications

General

Operating Temperature	-10°C to +50°C
Communication	RS485, Ethernet
Processor	ARM Cortex-A8
Operating System	Linux
Connectivity	Ethernet, Wi-Fi (optional)