What to do if my ELFON OPTIMA SL255 panel displays 'SHORT.LINE.' message?
If the ELFON Intercom System panel displays the message "SHORT.LINE.", it indicates a shorted handsets line. To resolve this, eliminate the short-circuit. After correcting the shorting issue, the panel may continue to display the shorting message for up to 10 seconds.
Why doesn't the code or RFID tag open the electric lock on my ELFON OPTIMA SL255?
If the general/individual code or RFID tag isn't opening the electric lock on your ELFON Intercom System, even without error messages, verify that the permission to open the electric lock using the general/individual code or RFID code is properly configured.
How to fix power grid hum during calls on my ELFON OPTIMA SL255?
If you hear a power grid hum during a conversation using the ELFON Intercom System, try the following: Increase the supply voltage (do not exceed 15VAC), increase the cross-sections of long supply cables, or increase the power of the central unit power supply if it's too low.
How to stop the peep sound on my ELFON OPTIMA SL255 Intercom System?
If you are experiencing a peep sound during talking or when putting down the handset receiver on your ELFON Intercom System, first reduce the sensitivity of the panel microphone (using the MICROPHONE potentiometer) or reduce the panel loudness (using the LOUDNESS potentiometer). For specific handsets, try adjusting the handset potentiometer (if available) or setting the balance (BALANCE potentiometer).
Why is handset No 1 dialled when dialing other handsets on my ELFON Intercom System?
If handset No 1 is sometimes dialled when dialling another handset on your ELFON Intercom System, change the handset No 1 addressing to another number.
Why does my ELFON OPTIMA SL255 panel display 'TRY AGAIN' in multi-entry mode?
If the ELFON Intercom System panel displays the message "TRY AGAIN" during each handset dialling attempt in a multi-entry system, ensure that each panel operating in the system has the same option selected - Multi-entry mode ("Two panels" or "OP- H4 mode"). Check the connection of each panel using the Communication test option. If using „OP-H4 mode”, verify that the communication module channels to which the panels are connected are activated. If using „OP-H4MS mode”, ensure one panel is connected to channel 0 of module OP-H4. Also, check if the panel data lines are connected with correct polarization.
Why does my ELFON OPTIMA SL255 say 'NUMBER NOT FOUND'?
If, after selecting a flat number, the ELFON Intercom System panel displays the message "NUMBER NOT FOUND", it indicates that the selected number has not been added to the operated ranges.
Why does my ELFON Intercom System panel return to the main message after selecting a flat?
If, after selecting a flat, the ELFON Intercom System panel immediately returns to the main message, it is because zero dialling time in general settings, zero ringing time in individual settings, or zero ringing time for the dialled physical number of the handset in individual settings is set.
Overview of different OPTIMA series panel models and their features.
Instructions for mounting the panel and connecting its power supply.
Explains panel terminals and guides audio system handset connection.
Instructions for setting up video systems with monitors and distributors.
Procedure for replacing the address tag on the entry panel.
Explains key functions in normal and menu operation modes.
Steps for initial panel setup, calibration, and potentiometer adjustment.
Guide on how to initiate a call or connection with a specific flat or handset.
Various methods to unlock the electric lock using codes, tags, or buttons.
Access to diagnostic tests, firmware version, and system setup.
Options for numbering and assigning flats to specific handsets.
Includes tests for picked up handsets and wrong polarization.
Activate installation mode for testing and check firmware version.
Manage service codes, RFID tags, and access control.
Verifies RFID tag status and its assignment within the system.
Shows the panel's unique serial number for identification.
Adjusts the sensitivity and performance of the RF reader module.
Assigns new general opening codes based on the panel serial number.
Assigns new individual opening codes based on the panel serial number.
Resets general system, individual user, and default code settings to factory defaults.
Clears stored RFID tags and individual access codes from memory.
Resets all panel configurations back to their factory default state.
Configures parameters like talking time, dialling time, and ringing time.
Configures electric lock buzz, magnetic mode, and unlocking duration.
Synchronizes relay settings with electric lock settings.
Configures ring tone, loudness, and ringing time for handsets.
Sets handset as door ring and enables electric lock unlocking via handset/RF tag.
Confirms wrong codes, activates relay, and configures entry codes.
Manages RF tags, handset power, and office mode activation.
Administrator controls user editing rights for various parameters.
Enables or disables user editing for all system parameters.
Details on setting up two-entry audio systems and data line connections.
Details on additional elements for multi-entry video systems.
General| Color | White |
|---|---|
| Display | LCD |
| Operating Voltage | 12V DC |
| Operating Temperature | -10°C to +50°C |
| Material | Plastic |
| Type | Video Intercom System |
To Next Page