Eltek Minipack - Battery Interface Card - Terminals & Pin-Out

Quick Start Guide Minipack PS System 356808.103, v1-2006-12
16
Battery Interface Card ~ Terminals & Pin-out
The Smartpack controller’s battery monitoring signals are accessible on D-Sub connectors
CON4 and CON3, on the controller’s rear panel.
Using the Battery Connection Kit ⎯ which consists of a Battery
Interface Card (Art. 200576) and a standard 15 pins D-Sub cable
⎯ you can make the signals on CON4 accessible at any suitable
location inside your system, e.g. near the battery blocks.
When extra battery monitoring signals are required, you can use an
extra Battery Connection Kit connected to the controller’s CON3.
For detailed information about the card’s pin-out location and
terminal block connections, see the figures in this section.
For temperature monitoring of the battery
compartment, we recommend the use of the
Temperature Sense Kit, instead of
connecting the sensor cable directly to the
terminals, pin 9-10.
The Temperature Sense Kit is connected to
the Battery Interface Card (Art. 200576), or
directly to the controller’s CON3 or CON4,
if unused.
15 pins D-Sub cable
Card Art.200576
Battery Connection Kit
Temp. senso
r
Temp. Sensor cable
Temperature Sense Kit
In
1.
5
mm
2
, max.
wire section
Battery Connections (Internal)
Configurable monitoring digital inputs
FUNCTION SIGNAL PIN-OUT
(
Internal Connections
)
4
3
2
1
5
9
8
7
6
10
14
13
12
11
X4
Batt. Symmetry 1
+
−
+
−
+
−
+
−
Batt. Symmetry 2
Batt. Symmetry 3
Batt. Symmetry 4
(From internal
batteries)
(From area with internal batteries)
Temperatu
r
e
senso
r
+
−
Temperature Sense 1
(NA)
(NA)
(From area with internal batteries)
Temperatu
r
e
senso
r
15-pins
D-Sub female
(Alternative use of Temp. Sense Kit,
instead of connecting to X4: 9-10)
Temperature Sense 1
X**/X*
15-pins D-Sub male
1
5
11 15
Card Art.200576
To Smartpack,
CON4
CON3A or
CON4A
15-pins
D-Sub female
111
515
In
1.
5
mm
2
, max.
wire section
Battery Connections (Internal)
Configurable monitoring digital inputs
FUNCTION SIGNAL PIN-OUT
(
Internal Connections
)
4
3
2
1
5
9
8
7
6
10
14
13
12
11
X3
+
−
+
−
+
−
+
−
(From internal
batteries)
(From area with internal batteries)
Temperatu
r
e
senso
r
+
−
(From area with internal batteries)
Temperatu
r
e
senso
r
15-pins
D-Sub female
(Alternative use of Temp. Sense Kit,
instead of connecting to X3: 9-10)
Temperature Sense 2
X**/X*
15-pins D-Sub male
1
5
11 15
Card Art.200576
To Smartpack,
CON3
CON3A or
CON4A
15-pins
D-Sub female
111
515
The Temperature Sense Kits may also be connected directly to the
Smartpack controller’s CON3 or CON4, if these connectors are unused.
Batt. Symmetry 5
Batt. Symmetry 6
Batt. Symmetry 7
Batt. Symmetry 8
Temperature Sense 2
Batt Current 2
Batt Fuse Fail 2
Miscellaneous Battery Monitoring
Battery Interface Card, Art. 200576
14
1
Serial Switch
For Temp. Sense Kit
CON3A or CON4A
X3/X4
X**/X*
1
Terminals & Pin-out Location
CON3
CON2
CON4
CON5
CON1
PCB 200576
PCB 200576
Smartpack