Powerdrive F300 Getting Started Guide 55
Issue Number: 5
Safety
information
Product
information
Mechanical
installation
Electrical
installation
Getting started
Basic parameters
(Menu 0)
Running the
motor
Optimization
NV Media Card
Operation
Further
information
UL listing
information
00.022
Bipolar Reference
Enable
{01.010} Off (0) or On (1) Off (0) RW Bit US
00.024 Preset Reference 1 {01.021} ±VM_SPEED_FREQ_REF Hz / rpm 0.0 Hz / rpm RW Num US
00.025 Preset Reference 2 {01.022} ±VM_SPEED_FREQ_REF Hz / rpm 0.0 Hz / rpm RW Num US
00.026
Preset Reference 3 {01.023}
±VM_SPEED_
FREQ_REF Hz
0.0 Hz RW Num US
Overspeed
Threshold
{03.008}
0 to 40000 rpm 0 rpm RW Num US
00.027 Preset Reference 4 {01.024}
±VM_SPEED_FRE
Q_REF Hz
0.0 Hz RW Num US
00.029
NV Media Card
Data Previously
Loaded
{11.036} 0 to 999 0 RO Num NC PT
00.030 Parameter Cloning {11.042}
None (0), Read (1), Program (2), Auto (3),
Boot (4)
None (0) RW Txt NC US
00.031 Rated Voltage {11.033} 200 V (0), 400 V (1), 575 V (2), 690 V (3)
RO Txt ND NC PT
00.033
Catch A
Spinning Motor
{06.009}
Disable (0),
Enable (1),
Fwd Only (2),
Rev Only (3)
Disable (0) RW Txt US
00.034 User Security Code {11.030} 0 to 2147483647 0 RW Num ND NC PT US
00.035 Serial Mode {11.024}
8 2 NP (0), 8 1 NP (1), 8 1 EP (2), 8 1 OP (3),
8 2 NP M (4), 8 1 NP M (5), 8 1 EP M (6),
8 1 OP M (7), 7 2 NP (8), 7 1 NP (9),
7 1 EP (10), 7 1 OP (11), 7 2 NP M (12),
7 1 NP M (13), 7 1 EP M (14), 7 1 OP M (15)
8 2 NP (0) RW Txt US
00.036 Serial Baud Rate {11.025}
300 (0), 600 (1), 1200 (2),
2400 (3), 4800 (4), 9600 (5), 19200 (6),
38400 (7), 57600 (8), 76800 (9), 15200 (10)
19200 (6) RW Txt US
00.037 Serial Address {11.023} 1 to 247 1 RW Num US
00.038
Current Controller
Kp Gain
{04.013} 0 to 30000 20 150 RW Num US
00.039
Current Controller
Ki Gain
{04.014} 0 to 30000 40 2000 RW Num US
00.040 Auto-tune {05.012} 0 to 2 0 to 5 0 to 6 0 RW Num NC
00.041
Maximum Switching
Frequency
{05.018}
2 kHz (0), 3 kHz (1), 4 kHz (2), 6 kHz (3),
8 kHz (4), 12 kHz (5), 16 kHz (6)
3 kHz (1) RW Txt RA US
00.042
Number Of Motor
Poles
{05.011} Automatic (0) to 480 Poles (240) Automatic (0)
6
Poles
(3)
RW Num US
00.043 Rated Power Factor {05.010} 0.000 to 1.000
0.850 RW Num RA US
00.044 Rated Voltage {05.009} ±VM_AC_VOLTAGE_SET V
200V drive: 230V 50Hz default
400V drive: 400V 60Hz default
400V drive: 460V
575V drive: 575V
690V drive: 690V
RW Num RA US
00.045 Rated Speed {05.008} 0 to 33000 rpm 0.00 to 33000.00 rpm
Eur - 1500 rpm
USA - 1800 rpm
Eur -
1450.0
0 rpm
USA -
1750.0
0 rpm
3000.0
0 rpm
RW Num US
00.046 Rated Current {05.007} ±VM_RATED_CURRENT A
Maximum Rated Current
(11.060) A
RW Num RA US
00.047
Rated Frequency {05.006} 0.0 to 550.0 Hz
50Hz: 50.0
60Hz: 60.0
RW Num US
Volts per 1000 rpm {05.033}
0 to
10000 V
/ 1000
rpm
98 V /
1000
rpm
RW Num US
00.048 User Drive Mode {11.031} Open-loop (1), RFC-A (2), RFC-S (3) Open-loop (1)
RFC-A
(2)
RFC-S
(3)
RW Txt ND NC PT
Parameter
Range Default
Type
OL RFC-A RFC-S OL RFC-A RFC-S
Powerdrive F300 Getting Started Guide English Iss2.book Page 55 Tuesday, July 28, 2015 3:23 PM
To Next Page
Loading...
