G
Glenn WrightSep 5, 2025
What to do if Endress+Hauser Measuring Instruments show error W153?
- DDonna SmithSep 5, 2025
If your Endress+Hauser Measuring Instruments display error W153, wait for completion of the initializing procedure.
To Next PageTo Next Page
What to do if Endress+Hauser Measuring Instruments show error W153?
If your Endress+Hauser Measuring Instruments display error W153, wait for completion of the initializing procedure.
What to do if Endress+Hauser Gammapilot M FMG60 show error W103?
If your Endress+Hauser Measuring Instruments display error W103, wait for completion of the initializing procedure.
What to do if Endress+Hauser Measuring Instruments show error A116?
If your Endress+Hauser Measuring Instruments display error A116, repeat the download.
What to do if Endress+Hauser Gammapilot M FMG60 Measuring Instruments show error A121?
If your Endress+Hauser Measuring Instruments display error A121 due to an electronics defect, first try switching the device off and then on again. If the error persists after restarting, contact Endress+Hauser service or consider replacing the transmitter.
What to do if density not calibrated on Endress+Hauser Gammapilot M FMG60 Measuring Instruments?
To resolve a 'density not calibrated' error with Endress+Hauser Measuring Instruments: * Verify that at least one calibration point has been entered and activated within the calibration function group. If not, enter and activate the necessary calibration points. * Ensure that the reference pulse rate is not larger than 232. If it is, re-perform the density calibration within the calibration function group.
What to do if Endress+Hauser Gammapilot M FMG60 Measuring Instruments show error A113?
If your Endress+Hauser Measuring Instruments display error A113 due to an electronics defect, first try switching the device off and then on again. If the error persists after restarting, contact Endress+Hauser service or consider replacing the transmitter.
What to do if Endress+Hauser Gammapilot M FMG60 show error A111?
If your Endress+Hauser Measuring Instruments display error A111 due to an electronics defect, first try switching the device off and then on again. If the error persists after restarting, contact Endress+Hauser service or consider replacing the transmitter.
What to do if Endress+Hauser Gammapilot M FMG60 Measuring Instruments show error A165?
If your Endress+Hauser Measuring Instruments display error A165 due to an electronics defect, first try switching the instrument off and then on again. If the error persists after restarting, contact Endress+Hauser service or consider replacing the transmitter.
What happens when Endress+Hauser Measuring Instruments issues a warning error?
When a warning error occurs, the Endress+Hauser Measuring Instruments device continues measurement, and an error message is displayed, alternating with the measured value.
What to do if Endress+Hauser Gammapilot M FMG60 Measuring Instruments shows the last error?
The last error is displayed in the "diagnostics" function group in the "previous error" function. The displayed item can be deleted in the "delete last error" function.
General| Measurement Principle | Gamma radiation absorption |
|---|---|
| Housing Material | Aluminum or stainless steel |
| Protection Class | IP66/67 |
| Radiation Source | Cesium-137 (Cs-137) or Cobalt-60 (Co-60) |
| Accuracy | ±1% of measuring range |
| Output Signal | 4 to 20 mA HART |
| Power Supply | 10.5 to 45 V DC |
| Ambient Temperature | -20 to +60 °C |
| Communication | HART |
| Certifications | ATEX, IECEx |
| Application | Density, level, or concentration measurement in liquids, solids, suspensions or slurries |
| Process Temperature | -40 to +80 °C |
