Endress+Hauser iTEMP HART TMT162

To Next Page

To Previous Page

Commissioning TMT162

22 Endress+Hauser

Note!

The sensor inputs (≥ SW 01.03.00) are no longer available in the Commuwin II PC configuration

software.

Function group SENSOR 1

Available in ReadWin

2000, HART

handheld module DXR275/375 (Symbol

Commuwin II with Matrix address

ReadWin

2000

/FieldCare CW II-

Matrix

Sensor type

IEC 751

JIS

IEC 751

Edison Copper

Winding No. 15

SAMA

Edison Curve

No. 7

GOST

Sensor type

Pt100

Pt200

Pt100

Pt500

Pt1000

Ni100

Ni1000

Cu10

Pt100

Ni120

Pt50

Pt100

Cu50

Cu100

Polynomial RTD

Callendar - van

Dusen (Pt100)

TC Type B

TC Type C

TC Type D

TC Type E

TC Type J

TC Type K

TC Type L

TC Type N

TC Type R

TC Type S

TC Type T

TC Type U

10 to 400 Ω

10 to 2000 Ω

-20 to 100 mV

Lower range

value

-328°F (-200 °C)

-76 °F (-60 °C)

-148 °F (-100 °C)

-94 °F (-70 °C)

-328°F (-200 °C)

32 °F (0 °C)

-454 °F (-270 °C)

-346 °F (-210 °C)

-454 °F (-270 °C)

-328°F (-200 °C)

-454 °F (-270 °C)

-58 °F (-50 °C)

-454 °F (-270 °C)

-328°F (-200 °C)

10 Ω

-20 mV

Upper range

value

1562 °F (850 °C)

1200 °F (649 °C)

482 °F (250 °C)

302 °F (150 °C)

500 °F (260 °C)

1292 °F (700 °C)

518 °F (270 °C)

2012 °F (1100 °C)

1562 °F (850 °C)

392 °F (200 °C)

1562 °F (850 °C)

3308 °F (1820 °C)

4208 °F (2320 °C)

4523 °F (2495 °C)

1832 °F (1000 °C)

2192 °F (1200 °C)

2501 °F (1372 °C)

1652 °F (900 °C)

2372 °F (1300 °C)

3214 °F (1768 °C)

752 °F (400 °C)

1112 °F (600 °C)

400 Ω

2000 Ω

100 mV

min. range

18 °F (10 °C)

900 °F (500 °C)

90 °F (50 °C)

900 °F (500 °C)

90 °F (50 °C)

10 Ω

100 Ω

5 mV

≥ SW 01.03.00

V3H0

Specific linearization and sensor matching

Selecting the sensor types 'Callendar-van-Dusen' or 'Polynomial RTD' improves the accuracy of the system or defines user-specific linearization of resistance

thermometers. A detailed description of the 'Callendar-van-Dusen' method and 'Polynomial RTD' linearization is provided in the Appendix to these Operating

Instructions.

Note!

The selection list of the sensor type is displayed depending on the PV unit. Example:

When selecting a resistance thermometer the PV unit must first be set to Ω.

Note!

Sensor 1 has priority, sensor 2 setup is matched to the setup of sensor 1.

Example: Sensor 1 is set up for a 4-wire connection, sensor 2 is set up for a 3-wire

connection; there is an automatic change of sensor 2 to a type K thermocouple.