Endress+Hauser Liquicap M FTI51 - Page 19

Liquicap M FTI51, FTI52 Installation
Endress+Hauser 19
Housing heights with adapter
Process connections
Polyester housing
F16
Stainless steel
housing F15
Aluminum housing
F17
Aluminum housing
F13*
Aluminum housing
with separate
connection
compartment T13*
L00-FTI5xxxx-06-05-xx-xx-044 L00-FTI5xxxx-06-05-xx-xx-046 L00-FTI5xxxx-06-05-xx-xx-045 L00-FTI5xxxx-06-05-xx-xx-048 L00-FTI5xxxx-06-05-xx-xx-047
Order code 21345
FTI51, FTI52
H1 144 142 152 194 202
* Housing with gas-tight process seal
H1
H1
H1
H1
H1
Thread G Thread NPT Threaded pipe joint Tri–Clamp Tri-Clamp clad
L00-FMI5xxxx-06-05-xx-yy-007
(DIN EN ISO228-I)
L00-FMI5xxxx-06-05-xx-yy-008
(ANSI B 1.20.1)
L00-FMI5xxxx-06-05-xx-xx-040
(EN 11851)
L00-FMI5xxxx-06-05-xx-xx-041
(ISO2852)
L00-FMI5xxxx-06-05-xx-xx-069
(ISO2852)
Rod probes ∅10, rope probes
For pressures up to 25 bar 25 bar 25 bar 16 bar** --
Version / order code G ½ / GCJ
G ¾ / GDJ
G 1 / GEJ
NPT ½ / RCJ
NPT ¾/ RDJ
NPT 1 / REJ
DN50 PN40 / MRJ DN25 (1") / TCJ
DN38 (1½") / TJJ
--
Dimensions H2 = 38
H3 = 19
AF = 41
H2 = 38
H3 = 19
AF = 41
H2 = 57 H2 = 57 --
Surface roughness -- -- ≤ 0.8 μm ≤ 0.8 μm--
Additional information Elastomer flat seal -- -- EHEDG*, 3A* --
Rod probes ∅14, rope probes
For pressures up to 25 bar 25 bar 25 bar 25 bar 25 bar 16 bar** 16 bar** 16 bar**
Version / order code G ¾ / GDJ
G 1 / GEJ
G 1½ /
GGJ
NPT ¾/
RDJ
NPT 1 /
REJ
NPT 1½/
RGJ
DN50 PN40 / MRJ DN25 (1") / TCJ
DN38 (1½") / TJJ
DN40-51 (2") / TDJ
DN38 /
TJK
(1½")
DN40-51
TDK
(2")
Dimensions H2 = 38
H3 = 19
AF = 41
H2 = 41
H3 = 25
AF = 55
H2 = 38
H3 = 19
AF = 41
H2 = 41
H3 = 25
AF = 55
H2 = 66 H2 = 66 H2 = 66
Surface roughness*** -- -- ≤ 0.8 μm ≤ 0.8 μm ≤ 0.8 μm
Additional information Elastomer flat seal -- -- EHEDG, 3A EHEDG, 3A
* The EHEDG, 3A certificate only applies to probes with a fully insulated probe rod. It does not apply to probes with an inactive length or active buildup
compensation.
** In the event of CRN approval, the maximum permitted process pressure is 11 bar.
*** Does not apply for inactive lengths.
H2
H3
AF
H2H3
AF
H2
H2
H2