Epson WF-7525 - Page 58

Epson WF-7520/7510/7010 series Revision A Disassembly/Reassembly Detailed Disassembly/Reassembly Procedure for each Part/Unit 58
ADF Cover (WF-7520/7510 series)
Tighten the screws in the order indicated in the figure above.
C.B.P-TITE SCREW 3x8 F/ZN-3C (6 ± 1 kgf·cm)
3
ADF Paper Guide Upper Assy
ADF Cover
1
2
4
ADF LD Assy (WF-7520/7510 series)
If the Cover Lock Release Link, the Cover Lock Release Middle Link or the Cover Lock Release Rear Link comes off when removing the ADF LD Assy, attach it back as shown above.
ADF LD Assy
Left
Lock Release Shaft
Right
Lock Release Shaft
Cover Lock
Release Link
Cover Lock
Release
Middle Link
Cover Lock Release Rear Link
Main Board Unit
Do not damage or contaminate the MAC Address Label. When replacing the Main Board, it is necessary to set the MAC address if the EEPROM data cannot be read out from the old Main Board. In such a case, refer to
“5.2.4 MAC Address Setting (p78)”
and set it.
Main Board Unit
MAC Address Label
Wireless LAN Module
Tighten the screws in the order indicated in the figure above.
1
Wireless LAN Module
C.B.S-TITE SCREW 3x6 F/ZN-3C (6 ± 1 kgf·cm)
2
Shield Plate Upper (w/ Wireless LAN Module)
Tighten the screws in the order indicated in the figure above.
C.B.S-TITE SCREW 3x6 F/ZN-3C (6 ± 1 kgf·cm)
C.P.SCREW 3x4 F/ZN-3C (2 ± 0.5 kgf·cm) C.B.S-TITE SCREW 3x10 F/ZN-3C (6 ± 1 kgf·cm)
1
2
3
4
5
WF-7010 series
WF-7520 series / WF-7510 series
7
Back
1
2
3
4
5
6
Shield Plate Upper
(w/ Wireless LAN Module)
C.B.S-TITE SCREW 3x6 F/ZN-3C (6 ± 1 kgf·cm)
C.P.SCREW 2.5x6 F/ZN-3C (2 ± 0.5 kgf·cm) C.P.SCREW 3x4 F/ZN-3C (2 ± 0.5 kgf·cm) C.B.S-TITE SCREW 3x10 F/ZN-3C (6 ± 1 kgf·cm)
6
Back
Shield Plate Upper
(w/ Wireless LAN Module)
Ink System Assy
 Align the dowels A to dowel D of the Ink System Assy with the hole A to hole D of the Frame Base Assy, and install the Ink System Assy to the
Frame Base Assy.
 Insert the Waste Ink Tube to the hole of the Frame Base Assy up to 8 ± 1 mm from the end of the tube.
C.B.P-TITE SCREW 3x10 F/ZN-3C (6 ± 1 kgf·cm)
C.B.P-TITE SCREW 3x10 F/ZN-3C (6 ± 1 kgf·cm) P.W. 3.5X0.5X12 F/ZN-3C
Frame Base Assy
B
A
D
C
B
A
D
C
Ink System Assy
Hole of Frame Base Assy
Waste Ink Tube
8 ± 1 mm
Rib
Frame Base Assy