ESAB 200i - Page 197

Manual 0560956430 197 TORCH DATA 100i-400i
Stainless Steel
Flow Rates (SLPM / SCFH)
400A
H17 N₂
Preow
- / - 207 / 439
H17 Plasma / N₂ Shield
Culow
47 / 100 173 / 367
Shield Cup
Shield Cap
Shield Gas
Distributor
Tip
Gas
Distributor
Electrode
Cartridge Assembly
This Art Is For Reference Only
Art# A-10444
Shield Cup Shield Cap
Shield Gas
Distributor
Tip Plasma Gas Distributor Electrode Cartridge
0559211401 0559210154 0559210083 0559210132 0559210065 0559210112 0559211400
Manual Gas Control Advanced Torch Height Control (THC) Basic THC CNC Control
Material
Thickness
Pre Flow
Pressure
(N₂)
Cut Flow Rates / Pressures
Arc
Voltage
Cut Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (H17) Shield (N₂)
ga (in) inch (psi) Ball (psi) Ball (psi) (Volts) (in) ±0.005 (sec) (in) (in) (sec) (in) (ipm) (sec) (in)
- 1/2 0.500 30 120 100 NA 100 141 0.180 0.4 0.375 0.000 0.2
Not Recommended
without Elevaon Height
105 0.4 0.205
- 5/8 0.625 30 120 100 NA 100 147 0.200 0.6 0.375 0.300 0.2 90 0.6 0.200
- 3/4 0.750 30 120 100 NA 100 150 0.200 1.0 0.375 0.300 0.2 70 0.7 0.210
- 1 1.000 30 120 100 NA 100 152 0.200 1.5 0.375 0.300 0.2 50 1.2 0.212
- 1 1/4 1.250 30 120 100 NA 100 164 0.300 2.0 0.375 0.400 0.2 38 1.4 0.235
- 1 1/2 1.500 30 120 100 NA 100 164 0.300 2.8 0.375 0.500 0.2 30 2.0 0.245
- 1 3/4 1.750 30 120 100 NA 100 170 0.300 5.0 0.375 0.750 0.2 21 3.0 0.255
- 2 2.000 30 120 100 NA 100 179 0.300 8.0 0.375 0.750 0.2 17 5.5 0.280
Manual Gas Control Advanced Torch Height Control (THC) Basic THC CNC Control
Material
Thickness
Pre Flow
Pressure
(N₂)
Cut Flow Rates / Pressures
Arc
Voltage
Cut Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (H17) Shield (N₂)
(mm) (Bar) Ball (Bar) Ball (Bar) (Volts) (mm) ±0.1 (sec) (mm) (mm) (sec) (mm)
(mm/
min)
(sec) (mm)
12 2.1 120 6.9 NA 6.9 140 4.5 0.4 9.5 0.0 0.2
Not Recommended without
Elevaon Height
2750 0.4 5.2
15 2.1 120 6.9 NA 6.9 145 4.9 0.5 9.5 5.5 0.2 2390 0.5 5.1
20 2.1 120 6.9 NA 6.9 150 5.1 1.1 9.5 7.6 0.2 1700 0.8 5.3
25 2.1 120 6.9 NA 6.9 152 5.1 1.5 9.5 7.6 0.2 1300 1.2 5.4
30 2.1 120 6.9 NA 6.9 161 6.9 1.9 9.5 9.5 0.2 1050 1.3 5.8
35 2.1 120 6.9 NA 6.9 164 7.6 2.4 9.5 11.5 0.2 860 1.7 6.1
40 2.1 120 6.9 NA 6.9 166 7.6 3.5 9.5 14.6 0.2 690 2.3 6.3
45 2.1 120 6.9 NA 6.9 171 7.6 5.3 9.5 19.1 0.2 520 3.2 6.5
50 2.1 120 6.9 NA 6.9 178 7.6 7.6 9.5 19.1 0.2 440 5.2 7.0
Marking
Pre Flow
Pressure
(N₂)
Marking Flow Rates /
Pressures
Arc
Voltage
Marking
Height
Pierce Ignion Height
THC and CNC
Delay
Control
Delay
Travel
Speed
Marking quality
degrades as
thickness
decreases.
50A Arc Current
Plasma (N₂) Shield (N₂)
Burn-through may
happen for thicknesses
< 1/16” (0.063”) /
1.6 mm.
(psi) /
(Bar)
Ball
(psi) /
(Bar)
Ball
(psi) /
(Bar)
(Volts)
(in) ±0.005 /
(mm) ±0.1
(in) ±0.005 / (mm) ±0.1 (sec) (sec)
(ipm) /
(mm/ min)
15 / 1.0 80
100 /
6.9
NA
100 /
6.9
135 0.120 / 3.0 0.120 / 3.0 0 0.4 0 / 0
BOLD TYPE indicates maximum piercing parameters. BOLD ITALIC indicates edge starts only.