EasyManua.ls Logo

ETS SunStar 332 - User Manual

ETS SunStar 332
36 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
26868-01A

Table of Contents

Questions and Answers

  • R
    Regina GonzalesAug 3, 2025
    What to do if my ETS SunStar 332 salon suffers frequent, short power outages?
    • C
      carloswilliamsAug 3, 2025
      If your salon experiences frequent, short power outages and clients are losing session time, and you have a T-Max® Manager, you can change parameter 23 from “0” to “1”. This will allow the ETS Personal Care Products tanning bed to remember the remaining time when the power goes out and resume the session after power is restored. Please consult your T-Max® Manager manual for information on setting parameters.
  • A
    Adam BowmanAug 9, 2025
    What to do if my ETS SunStar 332 bed displays '0' but not 'dL'?
    • K
      Kayla NelsonAug 9, 2025
      If your ETS Personal Care Products bed, connected to a T-Max® Manager, displays “0” a tanning time and the lamps have come on, but did not display “dL”, it may be due to several reasons: 1. The remote device has not been set. 2. The sunbed has not been connected to the remote system. 3. The delay time of the T-Max® Manager has not been set. 4. The delay time has expired and the session has begun or the auto-start function of the T-Max® Manager has been turned off. To resolve this, press the timer button to turn on the lamps.
  • K
    Kevin ShermanAug 18, 2025
    Why won't my ETS SunStar 332 sunbed function properly with a T-Max® 1A?
    • S
      Sarah NewmanAug 18, 2025
      If you are using a T-Max® 1A with your ETS Personal Care Products sunbed and it's not functioning correctly, SunStar® Bypass plugs or terminator plugs may be needed if the T-Max® 1A and the sunbed are over 100 feet apart. Install the plugs in the open remote port in the sunbed and the T- Max® 1A.
  • S
    susan74Aug 26, 2025
    What to do if the first bed doesn't register an 'id' when auto-addressing ETS SunStar 332?
    • E
      elizabeth13Aug 26, 2025
      When using the auto address feature of the T-Max® Manager with your ETS Personal Care Products bed, you must wait 10 seconds from the time you start the auto address function before addressing the first bed.

Summary

Safety Information

Installation Guide

Unpacking and Inspection

Details the process of unpacking and inspecting the sunbed unit upon arrival for completeness and damage.

Pre-Installation Planning

Covers crucial considerations before assembling the sunbed, including electrical requirements and room environment.

Tools Required for Assembly

Lists the necessary tools, such as a utility knife and Phillips screwdriver, for sunbed assembly.

Hardware Inventory

Provides a comprehensive list of all hardware components included for the sunbed assembly.

Assembly Procedures

Guides through the step-by-step process of assembling the sunbed, including stand and canopy setup.

Electrical Connections

Explains how to properly connect the sunbed's power cords and remote cables to the unit.

Final Assembly Steps

Details the final steps of assembly, including installing the air filter and front access panel.

Remote System Connections

Explains how to connect the sunbed to various remote control systems, including T-Max®.

Sunbed Operation

Pre-Tanning Precautions

Provides essential precautions and advice for users to follow before starting a tanning session.

Recommended Exposure Times

Outlines recommended tanning exposure times based on different skin types and tanning levels.

Using the Sunbed

Guides users on how to operate the sunbed, including controls, timer, and canopy operation.

Care and Maintenance

Cleaning After Each Use

Instructs on cleaning and disinfecting the sunbed's interior surfaces after each tanning session.

Thorough Periodic Cleaning

Details how to perform a more in-depth cleaning of the sunbed, including lamps and reflectors.

Mechanical Inspection Schedule

Provides guidelines for inspecting the sunbed's mechanical components for wear and proper function.

Lamp and Acrylic Replacement

Explains the procedure for replacing the sunbed's lamps and acrylic shields for optimal performance.

ETS SunStar 332 Specifications

General IconGeneral
BrandETS
ModelSunStar 332
CategoryPersonal Care Products
LanguageEnglish

Related product manuals