EverFocus EKB500 - 7.6.1.3 Home Position; 7.6.1.4 Autopan

EKB500_ma_en_rev1.5_3.doc 30
Back to home if no
action for ___Minute
Move to home position
[ENT] to confirm
Auto Back Enabled
[↑↓] to toggle
Speed:___[1-239]
[ENT] to start.
Position A
Dwell:___[1-239]
Move to Position B
[ENT] to confirm
Position B
Dwell:___[1-239]
Speed:___[1-239]
[ENT] to start.
Start preset
P
P
P
O
O
O
S
S
S
I
I
I
T
T
T
I
I
I
O
O
O
N
N
N
> enter preset number >
E
E
E
N
N
N
T
T
T
E
E
E
R
R
R
7.6.1.3 Home position
The home position is the position (preset) which is approached after a pre-defined duration upon last
speed dome operation.
S
S
S
E
E
E
T
T
T
(hold) +
H
H
H
O
O
O
M
M
M
E
E
E
> enter inactivity duration 1 ~ 999 minutes
> Enter
Use the
J
J
J
O
O
O
Y
Y
Y
S
S
S
T
T
T
I
I
I
C
C
C
K
K
K
to approach the requested position
>
E
E
E
N
N
N
T
T
T
E
E
E
R
R
R
Use the
J
J
J
O
O
O
Y
Y
Y
S
S
S
T
T
T
I
I
I
C
C
C
K
K
K
to activate the HOME function.
7.6.1.4 Autopan
End / stop definition:
S
S
S
E
E
E
T
T
T
(hold) +
A
A
A
.
.
.
P
P
P
A
A
A
N
N
N
Use the joystick to approach the requested position A,
enter the dwell time at this end stop in seconds
(
1
1
1
~
~
~
2
2
2
3
3
3
9
9
9
) >
E
E
E
N
N
N
T
T
T
E
E
E
R
R
R
Use the
J
J
J
O
O
O
Y
Y
Y
S
S
S
T
T
T
I
I
I
C
C
C
K
K
K
to approach the requested position B,
enter the dwell time at this end stop in seconds
(
1
1
1
~
~
~
2
2
2
3
3
3
9
9
9
) >
E
E
E
N
N
N
T
T
T
E
E
E
R
R
R
Activate A-B autopan
A
A
A
.
.
.
P
P
P
A
A
A
N
N
N
> enter pan speed
1
1
1
~
~
~
2
2
2
3
3
3
9
9
9
>
E
E
E
N
N
N
T
T
T
E
E
E
R
R
R
Activate 360° autopan
A continuous 360° pan operation is also possible.
S
S
S
H
H
H
I
I
I
F
F
F
T
T
T
(hold) +
A
A
A
.
.
.
P
P
P
A
A
A
N
N
N
> enter pan speed
1
1
1
~
~
~
2
2
2
3
3
3
9
9
9
>
E
E
E
N
N
N
T
T
T
E
E
E
R
R
R
Camera:0001 go to
Position:___[1-192]