36
ENGLISH ENGLISH
55
55
5
DIAGNOSTICSDIAGNOSTICS
DIAGNOSTICSDIAGNOSTICS
DIAGNOSTICS
5.1 940SDM5.1 940SDM
5.1 940SDM5.1 940SDM
5.1 940SDM
The door's hardware model and the software of the 940SDM
control board to which SD-Keeper is connected are shown.
5.2 NR. CYCLE5.2 NR. CYCLE
5.2 NR. CYCLE5.2 NR. CYCLE
5.2 NR. CYCLE
The count (non resettable )of the cycles effected by the door
is shown.
5.3 ALARM N.5.3 ALARM N.
5.3 ALARM N.5.3 ALARM N.
5.3 ALARM N.
The number and description of the current alarm are shown.
No.
DESCRIPTION MEANING
ENERGY SAV. Operating on low battery consumption
1 SPEED CHANGES Speed changed, new setup required
2 BAT.OPERATION. Door operating on battery
3 FORCED OPEN Door forced opening in progress
4 FLAT BATTERY Battery discharged: emergency movement not
guaranteed
6 EMERG 2 ON Emergency 2 input active
7 EMERG 1 ON Emergency 1 input active
8 OBST. IN OPEN. Opening obstacle detected 3 successive times;
Reset necessary to restore operation
9 OBST. IN CLOS. Closing obstacle detected 3 consecutive times;
Reset necessary to restore operation
10 콯 Lock locked in closed position
11 콯 Lock locked in open position (with surveillance kit only)
12 콯 Incorrect power supply to motor (VMOT absent)
13 콯 Photocell 2 faulty (PSW2 input)
14 콯 Photocell 1 faulty (PSW1 input)
15 콯 Setup not possible
18 콯 Initialisation process not possible on motor : leaf stroke
too long
20 콯 Initialisation process not possible on motor: insufficient
leaf stroke
22 콯 Initialisation process not possible on motor: too much
friction
24 콯 Motor malfunctions
25 콯 940SDM control board faulty
RESETRESET
RESETRESET
RESET
Executes reset procedure.
66
66
6
ADVANCED MENUADVANCED MENU
ADVANCED MENUADVANCED MENU
ADVANCED MENU
PP
PP
P
ASAS
ASAS
AS
SWORDSWORD
SWORDSWORD
SWORD
To access the advanced menu, insert the 4-digit password
(default 0000).
1 OPERA1 OPERA
1 OPERA1 OPERA
1 OPERA
TION PTION P
TION PTION P
TION P
ARAMETERSARAMETERS
ARAMETERSARAMETERS
ARAMETERS
1.1 CL1.1 CL
1.1 CL1.1 CL
1.1 CL
OSING SPEEDOSING SPEED
OSING SPEEDOSING SPEED
OSING SPEED
Sets door speed for closing.
When speed is changed with respect to the set value, an
alarm is signalled on the control board (“Error” LED flashing
slowly) and on the SD-Keeper (ALARM 1: speed change) - a
new Setup is recommended.
Standard value: level 3.
Adjusting range: from 0 to 10
1.2 OPENING SPEED1.2 OPENING SPEED
1.2 OPENING SPEED1.2 OPENING SPEED
1.2 OPENING SPEED
Sets door speed for opening.
Standard value: level 10 (maximum speed)
Adjusting range: from 0 to 10
1.3 DECEL. WIDTH1.3 DECEL. WIDTH
1.3 DECEL. WIDTH1.3 DECEL. WIDTH
1.3 DECEL. WIDTH
OpeningOpening
OpeningOpening
Opening
Sets anticipated time value on the standard deceleration
point at the opening stop position.
Standard value: 0 cm
Adjusting range: from 0 to 120 cm
ClosingClosing
ClosingClosing
Closing
Sets anticipated time value on the standard deceleration
point at the closing stop position.
Standard value: 0 cm
Adjusting range: from 0 to 120 cm
1.4 DECEL. SPEED.1.4 DECEL. SPEED.
1.4 DECEL. SPEED.1.4 DECEL. SPEED.
1.4 DECEL. SPEED.
Speed:Speed:
Speed:Speed:
Speed:
Sets speed level during deceleration.
Standard value: low
Adjusting range: high/medium/low
2 IN/OUT SETUP2 IN/OUT SETUP
2 IN/OUT SETUP2 IN/OUT SETUP
2 IN/OUT SETUP
2.1 Emerg 12.1 Emerg 1
2.1 Emerg 12.1 Emerg 1
2.1 Emerg 1
2.2 Emerg 22.2 Emerg 2
2.2 Emerg 22.2 Emerg 2
2.2 Emerg 2
Sets the effect of the emergency commands (Emerg1 and
Emerg2 inputs on 940SDM control board).
Standard setting EMERG 1:
Stop/No memory/NO
Standard setting EMERG 2:
Open/Speed: Standard/No memory/ NO
OpenOpen
OpenOpen
Open
Activating this command opens the door.
CloseClose
CloseClose
Close
Activating this command closes the door.
StopStop
StopStop
Stop
Activating this command stops the door.
Speed: StandardSpeed: Standard
Speed: StandardSpeed: Standard
Speed: Standard
The door opens or closes (according to setting) at normal speed.
Speed: No StandardSpeed: No Standard
Speed: No StandardSpeed: No Standard
Speed: No Standard
The door opens or closes (according to setting) at slow speed.
No memoryNo memory
No memoryNo memory
No memory
In order to keep the emergency active, the command must
be maintained active (on release, the door returns to normal
operation).
With memoryWith memory
With memoryWith memory
With memory
A pulse keeps the emergency operational;
To restore operation, resetting is necessary either from the control
board or from SD-Keeper.
NoNo
NoNo
No
Normally open input.
NcNc
NcNc
Nc
Normally closed input.
2.3 Photocells2.3 Photocells
2.3 Photocells2.3 Photocells
2.3 Photocells
QuantityQuantity
QuantityQuantity
Quantity
Number of connected photocells.
Standard no.: 2
Settable no.: 0, 1, 2
When no photocells are configured and the selected status is
NC (see below), there is no need to jumper connect unused
inputs.
When configuring 1 photocell, you can connect to the PSW1
input of the 940SDM control board.
Failsafe OffFailsafe Off
Failsafe OffFailsafe Off
Failsafe Off
Failsafe test on photocells not executed.
Failsafe OnFailsafe On
Failsafe OnFailsafe On
Failsafe On
Failsafe test on photocells executed before each movement.
NcNc
NcNc
Nc
Normally closed input.
NoNo
NoNo
No
Normally open input.
2.4 SENSORS2.4 SENSORS
2.4 SENSORS2.4 SENSORS
2.4 SENSORS
Sets the status of “external radar” and “internal radar”
commands (E-Det and I-Det inputs on 940SDM control board).
NoNo
NoNo
No
Normally open input.
NcNc
NcNc
Nc
Normally closed input.
2.5 KEY2.5 KEY
2.5 KEY2.5 KEY
2.5 KEY
Sets the status of the “key” command (Key input on the 940SDM
control board).
NoNo
NoNo
No
Normally open input.
NcNc
NcNc
Nc
Normally closed input.
To Next Page
Loading...
