E124S 24 532434 - Rev.A
Translation of the original instructions
ENGLISH
7. RADIO SYSTEM
The E124S is fitted with an integrated two-channel
decoding system that requires either a XF FDS or XF
radio module to be installed, to allow various types of
FAAC radio controls to be memorised.
- The XF FDS radio module allows you to memorise
FAAC radio controls with FDS coding. A maximum
of 251 codes can be memorised. FDS technology is
characterized by dual frequency transmission (433
and 868 MHz). XF FDS is not compatible with SLH,
SLH LR, LC/RC, DS radio controls.
- The XF433 or XF868 radio module allows you to
memorise FAAC radio controls that use the follow-
ing types of radio code: SLH, SLH LR, LC/RC, DS. It is
also possible to use FDS radio controls by following
a specific procedure to convert them into SLH mode
(see instructions). A maximum of 256 codes can
be memorised. The various types of radio codes
can coexist, but the radio module and all the radio
controls must have the same frequency.
The commands available are:
- OPEN A on radio channel 1 (CH1)
- OPEN B/CLOSE on radio channel 2 (CH2)
- Alternatively, the second radio channel can be
enabled to activate a programmable output (§ Ad-
vanced programming)
When it is switched on, the board detects the module
and activates the corresponding radio mode.
If the board detects a radio module that is not compat-
ible with any of the radio controls that have already
been memorised, the 2 RADIO LEDs flash alternately
to indicate the error. It is possible to delete the radio
controls, or install a compatible radio module.
L
To check which radio mode is active on the board, press
the
++ and
--
buttons at the same time.
The display shows the corresponding code (after any
Errors / Alarms that may be present):
SL compatible with SLH, SLH LR, LC/RC, DS radio
controls
Fd compatible with FDS radio controls
■ Memory full warning
If the RADIO LED on the board turns off instead of
flashing for 20 s during the radio control memorisation
procedure, it means that the radio memory is already
full and it is not possible to continue.
INSTALLING THE XF FDS OR XF RADIO
MODULE
1. The module should only be inserted into the con-
nector with the board switched off and on the side
indicated in the figure.
2. Only switch on power supply after having installed
the module. Then memorise the radio controls.
L
Follow the instructions to memorise the radio controls
according to their type.
Carry out the procedure with the radio control approxi-
mately 1 m away from the board.
7.1 MEMORISING XF FDS RADIO
CONTROLS
1. On the board, press the ++ (memorise OPEN
A) or
--
(memorise OPEN B/CLOSE) button and
release it when the corresponding RADIO LED
(RADIO1 or RADIO2) starts to flash for 20 s (time
available for the next step).
2. Press and release the button on the radio control
to be memorised. To confirm the memorisation,
the RADIO LED lights up steadily for 2 s and then
starts to flash again for another 20 s (time available
to repeat step 2 on another radio control).
The procedure ends after 20 s if no further radio
controls are memorised and the RADIO LED switches
off. To add additional radio controls, repeat the pro-
cedure from step 1.
7.2 MEMORISING SLH/SLH LR RADIO
CONTROLS
Memorise the first Master radio control on the
board. Afterwards, it is not necessary to access the
board in order to add radio controls.
To check if the radio control is a Master device, press
and hold a button and watch the LED:
- flashes briefly, then the light becomes
steady = Master
- turns on immediately with a steady light = NON
Master
To Next Page
Loading...
