E124S 25 532434 - Rev.A
Translation of the original instructions
ENGLISH
L
Whenever a new Master is memorised on the board,
any SLH/SLH LR radio controls that are already in use
are disabled.
MEMORISING THE FIRST RADIO CONTROL
MASTER
1. On the board, press the ++ (memorise OPEN A) or
--
(memorise OPEN B/CLOSE) button and release it
when the corresponding RADIO LED (RADIO1 or
RADIO2) starts to flash for 20 s (time available for
the next steps).
2. Press buttons P1 and P2 simultaneously on the
radio control and release them when LED on the
radio control starts to flash for 8 s (time available
for the next step).
3. Press and release the button on the radio control
to be memorised. To confirm the memorisation,
the RADIO LED on the board becomes steady for 1
s, then switches off.
When using the memorised button for the first time,
press it twice in succession to obtain the command.
ADDING SLH/SLH LR RADIO CONTROLS
1. Press buttons P1 and P2 simultaneously on the al-
ready memorised Master radio control and release
them when its LED on the radio control starts to
flash for 8 s (time available for the next step).
2. Within 8 s, press and hold the button that has
already been memorised, the LED lights up with
a steady light.
3. Bring the radio control that has already been
memorised, into contact face to face with the new
one to be memorised.
4. Press and hold the button on the new radio control
to be memorised. To confirm the memorisation,
the i radio control LED flashes twice and then
switches off.
5. Release the buttons.
When using the memorised button for the first time,
press it twice in succession to obtain the command.
7.3 MEMORISING LC/RC RADIO
CONTROLS
1. On the board, press the ++ (memorise OPEN A) or
--
(memorise OPEN B/CLOSE) button and release it
when the corresponding RADIO LED (RADIO1 or
RADIO2) starts to flash for 20 s (time available for
the next step).
2. Press and release the button on the radio control
to be memorised. To confirm the memorisation,
the RADIO LED lights up steadily for 2 s and then
starts to flash again for another 20 s (time available
to repeat step 2 on another radio control).
The procedure ends after 20 s if no further radio
controls are memorised and the RADIO LED switches
off. To add additional radio controls, repeat the
procedure from step 1.
ADDING LC/RC RADIO CONTROLS
Use a radio control that is already used by the automa-
tion, without having to adjust the board.
1. Take a LC/RC radio control that is already in use and
move close to the board.
2. Press buttons P1 and P2 simultaneously on the radio
control that is already in use and release them when
the LED on the radio control starts to flash slowly
for 5 s (time available for the next step).
3. Press and release the button that has already been
memorised (the corresponding RADIO LED on the
board starts to flash for 20 s, the time available for
the next step).
4. Press the button to be memorised on the new radio
control. To confirm the memorisation, the RADIO
LED lights up steadily for 2 s and then starts to flash
again for another 20 s (time available to repeat step
4 on another radio control).
The procedure ends after 20 s if no further radio
controls are memorised and the RADIO LED switches
off. To add additional radio controls, repeat the
procedure from step 1.
MEMORISING DS RADIO CONTROLS
1. Set the required combination of the DIP switches
on the radio control (avoid setting them to all ON
or all OFF).
2. On the board, press the
++ (memorise OPEN A) or
--
(memorise OPEN B/CLOSE) button and release it
when the corresponding RADIO LED (RADIO1 or
RADIO2) starts to flash for 20 s (time available for
the next step).
L
If the RADIO LED at step 2 turns off instead of flashing
for 20 s, it means that the radio memory is already full
and it is not possible to continue.
3. Press and release the button on the radio control
to be memorised. To confirm the memorisation,
the RADIO LED lights up steadily for 1 s, then
switches off.
4. To add other radio controls, you can set a DIP switch
combination that has already been memorised or
repeat the procedure for new combinations.
7.4 DELETING RADIO CONTROLS
L
This procedure cannot be reversed. It will delete ALL ra-
dio control codes of any type that have been memorised
as OPEN A and OPEN B/CLOSE. The deletion procedure
is only active when the display shows the automation
status.
1. Press the
--
button and DO NOT release it until the
To Next Page
Loading...
