FAAC S450H - Encoder Electrical Connection; Encoder Wiring and LED Indicators

8
FAAC Model S450H 24V Hydraulic Swing Gate Operator
TAB. 2
B
1
5.0 - 5.25 5.5-5.65 5.7-6.0 6.1-6.45 6.5-6.85 6.85-7.25 7.3-7.65 7.7-8.0 8.1-8.45 8.5-8.8 8.85-9.2 9.25-9.6
9.65-10.05
10.1-10.4
10.45-10.75
D
1
4.75-4.85
110° (1) 110° (1) 115° (1) 108° (1) 100° (1) 100° (1) 108° (2) 100° (2) 100° (2) 100° (3) 100° (3)
4.9-5.25
108° (1) 110° (1) 110° (1) 103° (1) 100° (1) 94° (1) 103° (2) 100° (2) 94° (2) 100° (3) 94° (3)
5.25-5.65
100° (1) 107° (1) 108° (1) 104° (1) 100° (1) 96° (1) 92° (1) 100° (2) 96° (2) 92° (2) 96° (3) 92° (3)
5.65-6.0
100° (1) 105° (1) 106° (1) 100° (1) 96° (1) 90° (1) 100° (2) 96° (2) 90° (2) 96° (3) 90° (3)
6.1-6.45
97° (1) 100° (1) 105° (1) 99° (1) 94° (1) 92° (1) 99° (2) 94° (2) 92° (2) 94° (3) 92° (3)
6.5-6.85
93° (1) 97° (1) 100° (1) 100° (1) 96° (1) 100° (2) 100° (2) 96° (2) 100° (3) 96° (3)
6.85-7.20
90° (1) 95° (1) 100° (1) 96° (1) 95° (2) 100° (2) 96° (2) 100° (3) 96° (3)
7.25-7.65
90° (1) 90° (1) 95° (1) 97° (1) 90° (2) 95° (2) 97° (2) 95° (3) 97° (3)
7.65-8.0
90° (1) 90° (1) 95° (1) 90° (2) 90° (2) 95° (2) 90° (3) 95° (3)
8.0-8.45
90° (1) 90° (1) 90° (2) 90° (2) 90° (2) 90° (3) 90° (3)
8.5-8.8
90° (1) 89° (2) 90° (2) 90° (2) 90° (2) 90° (3) 90° (3)
Z
a° (3)
a° (2)
D
1
a° (1)
(3)
(2)
(1)
TAB.2
B
1
XXX XXXX
D
1
XXX 115° (1) 115° (1)
XXX 110° (2) 110° (2)
XXX 100° (3) 100° (3)
B
1
2
3
4
3⅜
41¾
B
1
D
1
Z
a
- INTERSECT THE DIMENSIONS " D
1
" AND " B
1
" TO OBTAIN THE MAXIMUM VALUE OF OPENING ANGLES.
- ATTENTION: USE MECHANICAL LIMIT SWITCHES IN ORDER NOT TO EXCEED THE MAXIMUM OPENING ANGLES STATED IN TABLE 2 AND GUARANTEE
THE CORRECT OPERATION OF THE AUTOMATED SYSTEM.
HOLE TO BE USED ON THE REAR BRACKET
HOLE TO BE USED
ON THE REAR
BRACKET
INSTALLATION DIMENSION " B
1
"
(SEE FIGURE 4
1
-5
1
)
Dimensions in Inches
INSTALLATION
DIMENSION " D
1
" (SEE FIGURE 4
1
-5
1
)
Dimensions in Inches
Fig.5
1
Fig.4
1
3.1.2 APPLICATION WITH BRACKET FASTENED TO SIDE WALL
ATTENTION: do not cut the rear bracket for any reason.
Refer to Figures 4
1
and 5
1
and Table 2 to determine the installation position of the operator.